Alpine cda-9805, CDA-9807 owner manual 37-EN

Page 39
37-EN

1Antenna Receptacle

2Power Antenna Lead (Blue)

Connect this lead to the +B terminal of your power antenna, if applicable.

NOTE

This lead should be used only for controlling the vehicle's power antenna. Do not use this lead to turn on an amplifier or a signal processor, etc.

3Remote Turn-On Lead (Blue/White)

Connect this lead to the remote turn-on lead of your amplifier or signal processor.

4Audio Interrupt In Lead (Pink/Black)

5Illumination Lead (Orange)

This lead may be connected to the vehicle's instrument cluster illumination lead. This will allow the backlighting of the CDA-9807 to dim whenever the vehicle's lights are turned on.

6Switched Power Lead (Ignition) (Red)

Connect this lead to an open terminal on the vehicle's fuse box or another unused power source which provides (+)12V only when the ignition is turned on or in the accessory position.

7Battery Lead (Yellow)

Connect this lead to the positive (+) post of the vehicle's battery.

8Ground Lead (Black)

Connect this lead to a good chassis ground on the vehicle. Make sure the connection is made to bare metal and is securely fastened using the sheet metal screw provided.

9Fuse Holder (15A)

!Power Supply Connector

"Right Front (+) Speaker Output Lead (Gray)

#Right Front (–) Speaker Output Lead (Gray/Black)

$ Right Rear (–) Speaker Output Lead (Violet/Black)

%Right Rear (+) Speaker Output Lead (Violet)

&Left Rear (+) Speaker Output Lead (Green)

( Left Rear (–) Speaker Output Lead (Green/Black) ) Left Front (–) Speaker Output Lead (White/Black)

~Left Front (+) Speaker Output Lead (White)

+Ai-NET Connector

Connect this to the output or input connector of other product (CD Changer, Equalizer, etc.) equipped with Ai- NET.

NOTE

You can input TV/video sound by connecting an optional Ai- NET/RCA Interface cable (KCA-121B) to this component.

,Front Output RCA Connectors

RED is right and WHITE is left.

-Rear Output RCA Connectors

RED is right and WHITE is left.

. Subwoofer RCA Connectors

RED is right and WHITE is left.

/System Switch

When connecting a processor or divider using Ai-NET, place this switch in the EQ/DIV position. When no device is connected, leave the switch in the NORM position.

NOTE

Be sure to turn the power off to the unit before changing the switch position.

:Ai-NET Cable (Included with CD Changer)

;RCA Extension Cable (Sold Separately)

To prevent external noise from entering the audio system.

•Locate the unit and route the leads at least 10 cm away from the car harness.

•Keep the battery power leads as far away from other leads as possible.

•Connect the ground lead securely to a bare metal spot (remove any paint, dirt or grease if necessary) of the car chassis.

•If you add an optional noise suppressor, connect it as far away from the unit as possible. Your Alpine dealer carries various noise suppressors, contact them for further information.

•Your Alpine dealer knows best about noise prevention measures so consult your dealer for further information.

37-EN

Page 38 Page 40
Image 39
Page 38 Page 40
Contents FM/AM CD Receiver Please read before using this equipmentCDA-9807 CDA-9805CHA-S634 Alpine CD Changers Give You MoreChangeurs de CD Alpine vous avez le choix ¡Los cambiadores Alpine de CD le ofrecen másCD Player Operation SETUP OperationOperating Instructions Radio OperationXM Radio Operation Optional Installation and ConnectionsRemote Control Operation LIMITED WARRANTY3-EN PRECAUTIONSDisc Cleaning 4-ENPRECAUTIONS Installation LocationDetaching the Front Panel Turning Power On and OffBasic Operation Initial System Start-Upand Rear/Defeat Adjusting Volume/Balance BetweenSetting Time Left and Right/Fader Between Front7-EN Setting the Bass ControlSetting the Treble Control Setting the Bass TypeBasic Operation Setting the MX ModeBlackout Mode On and Off 8-EN9-EN Displaying the Title/TextBasic Operation Titling Discs/StationsErasing Disc Title/Station Title 10-EN11-EN SETUP OperationScroll Setting Subwoofer On and OffTurning Mute Mode On/Off Setting the External Input DefeatSetting the AUX Mode V-Link Mode13-EN Connecting to an External AmplifierRadio Operation Manual TuningAutomatic Seek Tuning Manual Storing of Station PresetsQuick Search Function Automatic Memory of Station PresetsTuning to Preset Stations Station Title Search Function16-EN CD Player OperationInserting/Ejecting Disc Normal Play and PauseM.I.X. Random Play Music Sensor SkipFast Forward and Backward Repeat Play18-EN Scanning ProgramsTrack Search Function Controlling CD Changer Optional19-EN Multi-ChangerSelection20-EN Playing MP3/WMA FilesPlaying MP3 Files with the CD Changer Optional CDA-9807only21-EN Scanning filesFolder/File Search Function Playing MP3 DataReceiving Stored XM Channels Storing XM Channel PresetsXM Radio Operation Optional Checking the XM Radio ID NumberChanging the Display Setting the tuning methodSetting the Auxiliary Data Field Display Channel/Category Search FunctionIncoming Calls MobileHub Link OperationOptionalAbout MobileHub Link Telephone Mode ON/OFFCalling by using the Speed Dial SMS Short Message Service OperationCalling 25-ENRemote Control Operation Controls on Remote Control CDA-9807only26-EN 27-EN Battery Replacement CDA-9807onlyInformation About MP3/WMA28-EN 29-EN TerminologyBasic In Case of Difficulty30-EN InformationHI TEMP ERRORERROR ERRORUPDATING 32-ENInformation ANTENNA33-EN SpecificationsInstallation and Connections Precautions34-EN 35-EN InstallationConnections 36-ENInstallation and Connections 37-EN Page LIMITED WARRANTY
Top Page Image Contents