Sharp MD-MX20 operation manual Setting the Clock, ON/STAND-BY Memory Enter

Page 12

Press the ON/STAND-BY button to turn the power on.

SETTING THE CLOCK

ON/STAND-BY	MEMORY/
ON/STAND-BY	ENTER
	Jog dial

CLOCK

●In this example, the clock is set for the 24-hour (0:00) sys- tem.

1

2 Press the CLOCK button.

6 Adjust the hour by turning the jog dial.

●When the jog dial is turned one click clockwise, the time will increase by 1 hour. When it is turned one click coun- terclockwise, the time will decrease by 1 hour.

Keep turning the jog dial to change the time continuously.

●When the 12-hour display is selected, “AM” will change automatically to “PM”.

7 Press the MEMORY/ENTER button.

8 Adjust the minutes by turning the jog dial.

●When the jog dial is turned one click clockwise, the time will increase by 1 minute. When it is turned one click coun- terclockwise, the time will decrease by 1 minute.

Keep turning the jog dial to change the time continuously.

●The hour setting will not advance even if minutes advance from "59" to "00".

9 Press the MEMORY/ENTER button.

●The clock starts operating from "0" second. (Seconds are not displayed.)

3 Within 5 seconds, press the MEMORY/ENTER button.

4 Turn the jog dial to select the time display mode.

"0:00" →The 24-hour display will appear. (0:00 - 23:59)

"12:00 AM" →The 12-hour display will appear. (AM or PM 12:00 - 11:59)

"0:00 AM" →The 12-hour display will appear. (AM or PM 0:00 - 11:59)

●Note that this can only be set when the unit is first in- stalled or it has been reset (see page 38).

5 Press the MEMORY/ENTER button.

To see the time display:

Press the CLOCK button.

●The time display will appear for about 5 seconds even in the stand-by mode.

Note:

●The "CLOCK" will appear at the push of the CLOCK button when the AC power supply is restored after a power failure occurs or after the AC power cord is disconnected.

If this happens, follow the procedure below to change the clock time.

To change the clock time:

1Press the CLOCK button.

2Within 5 seconds, press the MEMORY/ENTER button.

3Perform steps 6 - 9 above.

To change the time display mode:

1Reset the microcomputer (see page 38).

2Perform steps 2 - 9 above.

11

Image 12

Contents MD-MX20 Special Notes Please retain this informationImportant Safeguards Near water for example, near a bathtub, washbowlContents AccessoriesPrecautions Volume controlGeneral Care of compact discsNames of Controls and Indicators Front panelDisplay window Rear panelRemote control Speaker section Preparation for USE Antenna connectionSpeaker connection Connecting the AC power cord Demo modeRemoving the speaker grilles Placing the systemRemote control To change the brightness of the display Precautions for battery useWhen bright Lights up When dark Goes out DimmerSetting the Clock ON/STAND-BY Memory EnterClock Volume Sound ControlPre-programmed equalizer Extra bass X-BASSCompact Disc Operation CD playbackMinidisc Operation MiniDisc playbackTo remove a MiniDisc Press the MD 06 buttonConvenient CD and Minidisc Operations Apss Auto Program Search SystemCue and review MD/CD 3 MD/CDApms Automatic Programmable Music Selector CD HClear CD H MD H Repeat and random play ModeSwitching the time display Changing the display during MiniDisc playbackTime DisplayManual tuning Auto tuningPreset tuning Preset memory scanPreset Clear Memory EnterMinidisc Recording Differences from tape recordingsDisc writing TOC About track numbersTo cancel the operation Recording from a CD onto a MiniDisc One-Touch EditingTo check the remaining time available for record- ing To stop recordingTrack editing from a CD onto a MiniDisc To record without using One-Touch Editing Apms recording from a CD onto a MiniDiscPress the REC button Press the CD 06 buttonRecording from the built-in radio onto a MiniDisc To record the track number while recordingCheck the recordable time by pressing the Display button TIMER/DELETE Minidisc EditingWhat the editing function can do To create a disc nameTo create a track name To erase a track nameTIMER/DELETE NAME/TOC Edit 3 MD Memory Enter To change disc names and track namesJog dial To delete a character To add a characterWhen both tracks have a name Divide CombineTwo consecutive tracks can be combined into one track Press the MEMORY/ENTER button againMove Designated track can be moved to any desired positionErase All Erase Tracks you want to erase can be erased one at a timeTo erase tracks one at a time All of the tracks you want to erase can be erased at onceTimer Operation Timer playback/Timer recordingJog dial 2 CD H Tuner Band 2 AUXSimultaneous sleep and timer operation Sleep operationSTAND-BY Using External Units Connecting external unitsHeadphones Listening to sound from an external unit Manual recordingWhat is a MINIDISC? Troubleshooting If a problem occursMinidisc System Limitations GeneralResetting the Microcomputer Remote controlMiniDisc recording and playback Radio receptionError Messages Error messages Meaning RemedySymbol Number orMaintenance SpecificationsMemo Memo Where to Obtain Service What to do to Obtain Service Model Specific Section