Sharp MD-MX20 Minidisc System Limitations, Troubleshooting, If a problem occurs, General

Page 38

MINIDISC SYSTEM LIMITATIONS

Even if the maximum recording time of a	In the MD system, the delimiter of the recording area on a MiniDisc is
MiniDisc has not been reached, "TOC FULL"	programmed in a TOC. If partial erasing, recording and editing are re-
may be displayed.	peated several times, TOC information will fill up, even though the number
	of tracks has not reached the limit (255 tracks), and further recording will
	be impossible. (If you use the all erase function, this MiniDisc can be used
	from the beginning.)
Even if the maximum recording time of a	If there is any flaw on the MiniDisc, that part is automatically excluded
MiniDisc has not been reached, "DISC FULL"	from the space available for recording. Therefore, the recording time be-
may be displayed.	comes shorter.
Even if several short tracks are erased, the re-	When the remaining recording time of a disc is displayed, short tracks
maining recording time may not show an in-	less than 12 seconds long may not be included in the total.
crease.
Two tracks may not be combined in editing.	For MiniDiscs on which repeated recording and editing operations were
	performed, the COMBINE function may not work.
	A track recorded from a CD (digital recording) and a track recorded from a
	radio or other equipment (analog recording) cannot be combined.
The total of the recorded time and time remain-	A cluster (about 2 seconds) is normally the minimum unit of recording. So,
ing on a disc may not add up to the maximum	even if a track is less than 2 seconds long, it will use about 2 seconds of
possible recording time.	space on the disc. Therefore, the time actually available for recording may
	be less than the remaining time displayed.
	If there are scratches on discs, those sections will be automatically avoided
	(no recording will be placed in those sections). Therefore, the recording
	time will be reduced.
If recorded tracks are fast reversed or fast for-	A MiniDisc which has been recorded or edited repeatedly may skip during
warded, the sound may skip.	fast reverse or fast forward.

TROUBLESHOOTING

■ If a problem occurs

If this unit functions abnormally during operation, first check the following items. If the unit continues to function abnormally, or if an abnormality appears other than listed below, set this unit to the stand-by mode and disconnect the AC power plug, then consult your SHARP dealer or service personnel.

General

Symptom	Possible cause			Remedy

● The clock is wrong.	● Did a power failure occur?			● Try setting it again.
● When a button is pressed, the unit				● Set this unit to the stand-by mode
does not respond.				and then turn it back on. Then, retry
does not respond.				and then turn it back on. Then, retry
				the operation.
● No sound is heard.	● Is the volume level is set to "0"?			● Increase the volume level.
	● Are the headphones connected?			● Disconnect the headphones.
	● Are the speaker wires disconnected?			● Connect the wires securely.

● Radios make unusual noise or the	● When a radio or TV which uses an			● It is recommended that you use an
picture on the TV screen is distorted.	indoor antenna is placed near the			external antenna.
	unit, the picture on the TV screen
	may be distorted or the radio may
	not function properly.

CD Playback

	Symptom	Possible cause	Remedy

	● Even though a disc has been loaded,	● The disc is loaded up-side down.	● Load the disc with the correct side
	"NO DISC" is displayed.	● The disc is very dirty.	up.
	● Playback stops in the middle of a	● The disc is very dirty.	● Clean the disc.
	● Playback stops in the middle of a	● The disc does not satisfy the stan-	● Clean the disc.
	track, or playback is not performed	● The disc does not satisfy the stan-	● Load the correct disc.
	track, or playback is not performed	dards.	● Load the correct disc.
	properly.	● Is the unit located near excessive	● Place the unit on a firm, level sur-
	● Playback sounds are skipped.	● Is the unit located near excessive	● Place the unit on a firm, level sur-
	● Playback sounds are skipped.	vibrations?	face free from vibration.
		● Has condensation formed inside the	● Remove the disc and leave the
		unit?	power turned on. The unit should
			function properly in about 1 hour.

37

Image 38

Contents MD-MX20 Special Notes Please retain this informationImportant Safeguards Near water for example, near a bathtub, washbowlContents AccessoriesGeneral PrecautionsVolume control Care of compact discsNames of Controls and Indicators Front panelDisplay window Rear panelRemote control Speaker section Speaker connection Preparation for USEAntenna connection Removing the speaker grilles Connecting the AC power cordDemo mode Placing the systemWhen bright Lights up When dark Goes out Remote control To change the brightness of the displayPrecautions for battery use DimmerClock Setting the ClockON/STAND-BY Memory Enter Pre-programmed equalizer VolumeSound Control Extra bass X-BASSCompact Disc Operation CD playbackTo remove a MiniDisc Minidisc OperationMiniDisc playback Press the MD 06 buttonCue and review Convenient CD and Minidisc OperationsApss Auto Program Search System MD/CD 3 MD/CDClear CD H MD H Apms Automatic Programmable Music SelectorCD H Repeat and random play ModeTime Switching the time displayChanging the display during MiniDisc playback DisplayManual tuning Auto tuningPreset Preset tuningPreset memory scan Clear Memory EnterDisc writing TOC Minidisc RecordingDifferences from tape recordings About track numbersTo check the remaining time available for record- ing To cancel the operationRecording from a CD onto a MiniDisc One-Touch Editing To stop recordingTrack editing from a CD onto a MiniDisc Press the REC button To record without using One-Touch EditingApms recording from a CD onto a MiniDisc Press the CD 06 buttonCheck the recordable time by pressing the Display button Recording from the built-in radio onto a MiniDiscTo record the track number while recording What the editing function can do TIMER/DELETEMinidisc Editing To create a disc nameTo create a track name To erase a track nameJog dial To delete a character TIMER/DELETE NAME/TOC Edit 3 MD Memory EnterTo change disc names and track names To add a characterTwo consecutive tracks can be combined into one track When both tracks have a nameDivide Combine Press the MEMORY/ENTER button againMove Designated track can be moved to any desired positionTo erase tracks one at a time Erase All EraseTracks you want to erase can be erased one at a time All of the tracks you want to erase can be erased at onceJog dial 2 CD H Timer OperationTimer playback/Timer recording Tuner Band 2 AUXSTAND-BY Simultaneous sleep and timer operationSleep operation Headphones Using External UnitsConnecting external units Listening to sound from an external unit Manual recordingWhat is a MINIDISC? Minidisc System Limitations TroubleshootingIf a problem occurs GeneralMiniDisc recording and playback Resetting the MicrocomputerRemote control Radio receptionSymbol Error MessagesError messages Meaning Remedy Number orMaintenance SpecificationsMemo Memo Where to Obtain Service What to do to Obtain Service Model Specific Section