Sharp MD-MX20 Recording from a CD onto a MiniDisc One-Touch Editing, To cancel the operation

Page 23

(Continued)

Recording from a CD onto a MiniDisc (One-Touch Editing)

A CD can be recorded to a MiniDisc, starting from the first track, with one-touch operation.

MD H

1

4

3

2

1 Press the ON/STAND-BY button to turn the power on.

2 Press the CD button.

3 Load a CD and a recordable MiniDisc.

The total number of tracks and the total playing time on the CD will be displayed.

4 Press the CD 0 MD EDIT (HIGH or NORMAL) button.

Press the NORMAL button for actual speed, HIGH for high- speed recording.

0

REC

Recording will begin, starting from the first track of CD.

After recording (all of the tracks that can be recorded), the unit will stop automatically.

To check the remaining time available for record- ing:

1Press the MD ■ button.

2Load a MiniDisc.

3Press the DISPLAY button to find the time followed by hyphen.

The total number of tracks previously recorded and the available remaining time will be displayed, the unit will re- turn to the original display 4 seconds later.

To cancel the operation:

Before pressing the CD 0 MD EDIT (HIGH or NORMAL) button, press the CD ■ button.

To stop recording:

Press the MD ■ button.

Playback and recording will stop and the track numbers will be written on the MiniDisc.

Caution:

When a recording is made at high speed, the playback sound will not be heard.

Check whether recording is performed or not with the level meters.

You cannot adjust the sound volume. "VOL HOLD" appears when you adjust the sound volume while recording at high speed.

When a damaged CD is recorded at high speed, the unit may stop while recording, or some noise or a drop out may be recorded. In this case, record the CD at normal speed.

Notes:

When the CD playing time is longer than the available MiniDisc recording time, the recording process will not start even when the CD 0 MD EDIT button is pressed.

Total number of

Available record-

recordable tracks

ing time

(from the first track)

 

To record as many tracks as are available, press the CD 0 MD EDIT button again.

Then, when the CD 0 MD EDIT button is pressed again, recording will start. However, when the MiniDisc runs out of space, "DISC FULL" will be displayed and the CD and MiniDisc will stop.

However, if the available recording time on the MiniDisc is less than the length of the first track on the CD, recording will not be performed.

22

Image 23
Contents MD-MX20 Please retain this information Special NotesNear water for example, near a bathtub, washbowl Important SafeguardsAccessories ContentsCare of compact discs PrecautionsVolume control GeneralFront panel Names of Controls and IndicatorsRear panel Display windowRemote control Speaker section Speaker connection Preparation for USEAntenna connection Placing the system Connecting the AC power cordDemo mode Removing the speaker grillesDimmer Remote control To change the brightness of the displayPrecautions for battery use When bright Lights up When dark Goes outClock Setting the ClockON/STAND-BY Memory Enter Extra bass X-BASS VolumeSound Control Pre-programmed equalizerCD playback Compact Disc OperationPress the MD 06 button Minidisc OperationMiniDisc playback To remove a MiniDiscMD/CD 3 MD/CD Convenient CD and Minidisc OperationsApss Auto Program Search System Cue and reviewClear CD H MD H Apms Automatic Programmable Music SelectorCD H Mode Repeat and random playDisplay Switching the time displayChanging the display during MiniDisc playback TimeAuto tuning Manual tuningClear Memory Enter Preset tuningPreset memory scan PresetAbout track numbers Minidisc RecordingDifferences from tape recordings Disc writing TOCTo stop recording To cancel the operationRecording from a CD onto a MiniDisc One-Touch Editing To check the remaining time available for record- ingTrack editing from a CD onto a MiniDisc Press the CD 06 button To record without using One-Touch EditingApms recording from a CD onto a MiniDisc Press the REC buttonCheck the recordable time by pressing the Display button Recording from the built-in radio onto a MiniDiscTo record the track number while recording To create a disc name TIMER/DELETEMinidisc Editing What the editing function can doTo erase a track name To create a track nameTo add a character TIMER/DELETE NAME/TOC Edit 3 MD Memory EnterTo change disc names and track names Jog dial To delete a characterPress the MEMORY/ENTER button again When both tracks have a nameDivide Combine Two consecutive tracks can be combined into one trackDesignated track can be moved to any desired position MoveAll of the tracks you want to erase can be erased at once Erase All EraseTracks you want to erase can be erased one at a time To erase tracks one at a timeTuner Band 2 AUX Timer OperationTimer playback/Timer recording Jog dial 2 CD HSTAND-BY Simultaneous sleep and timer operationSleep operation Headphones Using External UnitsConnecting external units Manual recording Listening to sound from an external unitWhat is a MINIDISC? General TroubleshootingIf a problem occurs Minidisc System LimitationsRadio reception Resetting the MicrocomputerRemote control MiniDisc recording and playbackNumber or Error MessagesError messages Meaning Remedy SymbolSpecifications MaintenanceMemo Memo Model Specific Section Where to Obtain Service What to do to Obtain Service