Sharp MD-MX20 operation manual Preset tuning, Preset memory scan, Clear Memory Enter

Page 21

(Continued)

Preset tuning

You can store up to 40 stations in memory (40 stations con- sisting of any combination of AM and FM stations you like) and recall them.

2,4 3

3

2,4

To enter stations into memory:

1 Perform steps 1 - 5 in the "Tuning" section.

2 Press the MEMORY/ENTER button.

MEMORY

3 Within 5 seconds, turn the jog dial or press the PRE- SET (Xor W) button to make the preset channel num- ber flash in the display.

Store the stations in memory, in order, starting with preset channel 1.

When is displayed, a station has already been stored in this preset number memory.

4 Within 5 seconds, press the MEMORY/ENTER button to store that station in the selected station preset num- ber memory.

MEMORY

If the "MEMORY" and preset number indicators go out before the station is memorized, repeat the operation from step 2.

5 Repeat steps 1 - 4 to set other stations, or to change a preset station.

When a new station is stored in the selected station pre- set number memory location, the previously memorized station in that location will be erased.

To recall a memorized station:

Turn the jog dial or press the PRESET (X or W) button for less than 0.5 seconds to select the desired station.

The stations (preset channel number, frequency and fre- quency band) which have been stored in memory will ap- pear in the display in numerical order, irrespective of the frequency bands.

Backup function:

The backup function protects all station presets for a few hours should there be a power failure or the AC power cord is re- moved from the AC outlet.

Preset memory scan

The stations saved in the preset memory can be scanned automatically.

 

PRESET

CLEAR

(X W)

 

MEMORY/

 

ENTER

 

1 To scan the preset stations, press the PRESET (X or W) button for more than 0.5 seconds.

The station preset number will flash and the programmed stations will be tuned in sequentially, for 5 seconds each.

2 Press the PRESET (X or W) button again to stop the memory scan at the desired station.

Note:

When the preset memory does not have any stations stored in it, the preset memory scan will not function.

To erase the memorized station:

1 Recall the memorized station to be erased by turning the jog dial or pressing the PRESET (X or W) button.

2 Press the CLEAR button.

"MEMORY" and preset number will flash.

3 Within 5 seconds, press the MEMORY/ENTER button.

4 Repeat steps 1-3 to erase other memorized stations.

To erase all memorized stations:

When the unit is in the stand-by mode, hold down the TUNER (BAND) and the MD ■ buttons, and then press the ON/ STAND-BY button.

"PRESET CLR" will appear.

20

Image 21
Contents MD-MX20 Please retain this information Special NotesNear water for example, near a bathtub, washbowl Important SafeguardsAccessories ContentsVolume control PrecautionsGeneral Care of compact discsFront panel Names of Controls and IndicatorsRear panel Display windowRemote control Speaker section Preparation for USE Antenna connectionSpeaker connection Demo mode Connecting the AC power cordRemoving the speaker grilles Placing the systemPrecautions for battery use Remote control To change the brightness of the displayWhen bright Lights up When dark Goes out DimmerSetting the Clock ON/STAND-BY Memory EnterClock Sound Control VolumePre-programmed equalizer Extra bass X-BASSCD playback Compact Disc OperationMiniDisc playback Minidisc OperationTo remove a MiniDisc Press the MD 06 buttonApss Auto Program Search System Convenient CD and Minidisc OperationsCue and review MD/CD 3 MD/CDApms Automatic Programmable Music Selector CD HClear CD H MD H Mode Repeat and random playChanging the display during MiniDisc playback Switching the time displayTime DisplayAuto tuning Manual tuningPreset memory scan Preset tuningPreset Clear Memory EnterDifferences from tape recordings Minidisc RecordingDisc writing TOC About track numbersRecording from a CD onto a MiniDisc One-Touch Editing To cancel the operationTo check the remaining time available for record- ing To stop recordingTrack editing from a CD onto a MiniDisc Apms recording from a CD onto a MiniDisc To record without using One-Touch EditingPress the REC button Press the CD 06 buttonRecording from the built-in radio onto a MiniDisc To record the track number while recordingCheck the recordable time by pressing the Display button Minidisc Editing TIMER/DELETEWhat the editing function can do To create a disc nameTo erase a track name To create a track nameTo change disc names and track names TIMER/DELETE NAME/TOC Edit 3 MD Memory EnterJog dial To delete a character To add a characterDivide Combine When both tracks have a nameTwo consecutive tracks can be combined into one track Press the MEMORY/ENTER button againDesignated track can be moved to any desired position MoveTracks you want to erase can be erased one at a time Erase All EraseTo erase tracks one at a time All of the tracks you want to erase can be erased at onceTimer playback/Timer recording Timer OperationJog dial 2 CD H Tuner Band 2 AUXSimultaneous sleep and timer operation Sleep operationSTAND-BY Using External Units Connecting external unitsHeadphones Manual recording Listening to sound from an external unitWhat is a MINIDISC? If a problem occurs TroubleshootingMinidisc System Limitations GeneralRemote control Resetting the MicrocomputerMiniDisc recording and playback Radio receptionError messages Meaning Remedy Error MessagesSymbol Number orSpecifications MaintenanceMemo Memo Model Specific Section Where to Obtain Service What to do to Obtain Service