Sharp MD-MX20 operation manual Special Notes, Please retain this information

Page 2

SPECIAL NOTES

The lightning flash with arrowhead symbol, within an equilateral trian- gle, is intended to alert the user to the presence of uninsulated “dan- gerous voltage” within the prod- uct’s enclosure that may be of suf- ficient magnitude to constitute a risk of electric shock to persons.

C A U T I O N

R I S K O F E L E C T R I C S H O C K

D O N O T O P E N

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).

NO USER- SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSON- NEL.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and mainte- nance (servicing) instructions in the literature accompanying the appliance.

Caution - use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous ra- diation exposure.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EX- POSE THIS APPLIANCE TO RAIN OR MOISTURE.

Note:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio fre- quency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not oc- cur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and re- ceiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

WARNING

FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment.

It is the intent of Sharp that this product be used in full compliance with the copyright laws of the United States and that prior permission be obtained from copyright own- ers whenever necessary.

US and foreign patents licensed from Dolby Laboratories Licensing Corporation.

FOR YOUR RECORDS

For your assistance in reporting this unit in case of loss or theft, please record below the model number and serial number which are located on the rear of the unit.

Please retain this information.

Model number ______________________

Serial number_______________________

Date of purchase ____________________

Place of purchase ___________________

1

Image 2
Contents MD-MX20 Special Notes Please retain this informationImportant Safeguards Near water for example, near a bathtub, washbowlContents AccessoriesGeneral PrecautionsVolume control Care of compact discsNames of Controls and Indicators Front panelDisplay window Rear panelRemote control Speaker section Speaker connection Preparation for USEAntenna connection Removing the speaker grilles Connecting the AC power cordDemo mode Placing the systemWhen bright Lights up When dark Goes out Remote control To change the brightness of the displayPrecautions for battery use DimmerClock Setting the ClockON/STAND-BY Memory Enter Pre-programmed equalizer VolumeSound Control Extra bass X-BASSCompact Disc Operation CD playbackTo remove a MiniDisc Minidisc OperationMiniDisc playback Press the MD 06 buttonCue and review Convenient CD and Minidisc OperationsApss Auto Program Search System MD/CD 3 MD/CDClear CD H MD H Apms Automatic Programmable Music SelectorCD H Repeat and random play ModeTime Switching the time displayChanging the display during MiniDisc playback DisplayManual tuning Auto tuningPreset Preset tuningPreset memory scan Clear Memory EnterDisc writing TOC Minidisc RecordingDifferences from tape recordings About track numbersTo check the remaining time available for record- ing To cancel the operationRecording from a CD onto a MiniDisc One-Touch Editing To stop recordingTrack editing from a CD onto a MiniDisc Press the REC button To record without using One-Touch EditingApms recording from a CD onto a MiniDisc Press the CD 06 buttonCheck the recordable time by pressing the Display button Recording from the built-in radio onto a MiniDiscTo record the track number while recording What the editing function can do TIMER/DELETEMinidisc Editing To create a disc nameTo create a track name To erase a track nameJog dial To delete a character TIMER/DELETE NAME/TOC Edit 3 MD Memory EnterTo change disc names and track names To add a characterTwo consecutive tracks can be combined into one track When both tracks have a nameDivide Combine Press the MEMORY/ENTER button againMove Designated track can be moved to any desired positionTo erase tracks one at a time Erase All EraseTracks you want to erase can be erased one at a time All of the tracks you want to erase can be erased at onceJog dial 2 CD H Timer OperationTimer playback/Timer recording Tuner Band 2 AUXSTAND-BY Simultaneous sleep and timer operationSleep operation Headphones Using External UnitsConnecting external units Listening to sound from an external unit Manual recordingWhat is a MINIDISC? Minidisc System Limitations TroubleshootingIf a problem occurs GeneralMiniDisc recording and playback Resetting the MicrocomputerRemote control Radio receptionSymbol Error MessagesError messages Meaning Remedy Number orMaintenance SpecificationsMemo Memo Where to Obtain Service What to do to Obtain Service Model Specific Section