ClearOne comm 600/900 user manual Connecting VCRs and DVD players, Connecting PTZ cameras

Page 13

20

Connecting the RAV — Auxiliary Devices

Connecting VCRs and DVD players

You can record your audio/video conference or play audio using a playback device such as a VCR or DVD player.

Note: You can also connect a mono-signal device or a non-record/playback device to these line in/out connectors.

 

PLAYBACK / RECORD

L

L

IN

OUT

R

R

Figure 2.14. Connecting a Record/Playback device

To connect to record/playback

For recording, connect the Left and Right Audio Out on the RAV to the left and right audio in on the VCR or DVD player.

For playback, connect the Left and Right Audio In on the RAV to the left and right out on the VCR or DVD player.

Connecting PTZ cameras

The RAV system provides voice-tracking capabilities through VISCA control port connection to a Pan,Tilt, Zoom camera. Voice Tracking allows the camera to move to preset positions based on microphone activation. For instructions on programming the presets, see page 42.

CAMERA

CONTROL

Figure 2.15. Connecting a camera

To add a camera

Connect the camera to the Camera Control port on the mixer.

Note:The camera video out signal connects to a video codec.

Connecting the RAV— Auxiliary Devices

 

21

 

Connecting for serial control

You can connect a computer or a control device, such as an AMX or Crestron, to the RAV mixer through the serial control port. See the page 78 for a list of the serial commands.

To connect a computer serial port

Connect computer to Control port on the back of the mixer using a 9-pin serial cable.

LEPHONE

 

 

RS-232

CAMERA

LAN

CONTROL

SET

 

 

Figure 2.16. Connecting a computer serially

Connecting for USB control

You can also connect a computer to the RAV through the USB port.

To connect a computer through the USB port

Connect computer to the USB port on the front of the mixer using a USB cable.

Figure 2.17. Connecting a computer through the USB

Note:The USB drivers are installed when you install RAV-Ware.

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Image 13
Contents Page Table of Contents Introduction RAV 600/900 Services and supportProduct returns UnpackingRF Radio Frequency Controller Product OverviewMixer Basic Room Design Microphone PodsBasic Room Design for RAV Speakers ceiling- or wall-mountInstallation Overview Network Information System Requirements for RAV-WareWindows 98 SE Connecting the RAV Connecting the RAV Basic Connections To set up audio conferencingBasic Connections Audio conferencingAttach external antenna Insert four AAA batteries into the RF controllerAuxiliary Devices Connecting video codecs, amplifiers and sound cardsTo connect to a video codec To connect to a sound cardConnecting PTZ cameras Connecting VCRs and DVD playersConnecting for serial control Connecting for USB controlTo connect to a digital phone Digital phonesRAV-Ware Software Configuration Introduction Install RAV-WareGetting started with RAV-Ware RAV-Ware overviewRAV-Ware files RAV-Ware connectionsCommunication Settings Configuring System SettingsNetwork Find Telephone Settings Regional SettingsMicrophones Customizing RAV ComponentsMixer Console Effects of using an external amplifierAdjusting Line Input/Output settings Preconfigured video codecs, amplifiers and sound cardsLine Input and Output Preconfigured record/playback devices Adjusting Record/Playback settingsRecord and Playback Camera Controls Setting camera presetsDialer and Phonebook Usage PhonebookDialer System Checks Advanced FeaturesEvent Log Firmware upgrades Error MessagesDevice Toolbox Editor Using the RAV Managing Calls Using the ControllerAccessing the menu Using the Phonebook from the RF ControllerTo delete a Phonebook entry To access the menu Programming Phone PreferencesConfiguration Adjusting the SettingsTo perform RF radio test To select a frequencyTo enter flash duration To change LCD contrastDisplay Select Exit to return to the Configuration window Select Exit to return to the Configuration windowTo view the IP address To check the RAV versionWeb Interface Overview Accessing the web interfaceDial To connect to RAV through the web interfaceTo clear log To open event logTo download log Log Out System CheckTo open the system checks Click Yes, Log OutAppendix Troubleshooting MaintenanceAudio ControllerPinouts SpeakersCamera pinouts GeneralSpecifications Conventions Command structureGroups and channels Type and device IDsRAV serial commands Serial command error codesMeter type definitions Aarings Number of Rings to Auto Answer On AA Auto Answer Enable/ DisableName Type Size Values Units AEC Acoustic Echo Canceller enable/ disable AD Auto Disconnect Enable/ DisableAecref Acoustic Echo Cancellation Reference Aconn Audible Connect / Disconnect IndicationCamctrlmode Camera Control Port Mode Batterylvl Battery LevelBaud Baud Rate Calldur Call DurationCampresetset Camera Preset Setup Campreset Camera PresetCamflow Camera Control Flow Control Cammove Move the CameraCamswitchlag Camera Switch Time Lag CAMPRESETSET2 Camera Preset SetupCamposition Camera Position Camtrack Camera TrackCleareffect Clear Effect Wide Band Telco Emulation Default Default The UnitClock Clock Set Country Country SelectionDial Dtmf Dialing Device Device Identification LabelDid Device ID Enetaddr Ethernet port IP address Enetgate Ethernet default Gateway addressEnetdhcp Ethernet Dhcp Selection Enetdnsa Ethernet DNS Server addressesGain Gain Adjustment Eqsel Equalization EnableEQ Equalization Flow Flow ControlHook Hook Flash Greport Gate ReportHookd Hook Flash Duration Label LabelLVL Level Lvlreporten Level Report EnableLvlreport Level Report Manufacturer Manufacturer Identification LabelNcsel Noise Cancellation Select Miccampreset Mic Camera PresetMtrx Matrix Routing Mute MutePhonebookadd Adds an Entry to the Phonebook Pbdial Dial a PB Entry by NamePhonebookcnt Queries the Number of Entries in the Phonebook Phonebookdel Deletes an Entry to the PhonebookRedial Dial the last number again Reset ResetRffreq RF Frequency Selection Ring Ring IndicationRingerlvl Audible Ring Level Silenceprst Silence Camera PresetRingersel Audible Ring Melody Selection Ringertest Audible Ring Melody TestSyschecks System Checks Stereomix Sets the Input to be a Stereo MixSysresult System Check Result Telcolvlctrl Telco TX Level Control Enable/ Disable TE Telco EnableVolume Volume Adjustment UID Unit IDCompliance Electrical Safety AdvisoryFCC Part 15/ICES-003 Compliance FCC Part 68 ComplianceEuropean Compliance New Zealand ComplianceEC Declaration of Conformity Index

600/900 specifications

ClearOne’s COMM 600 and COMM 900 series are state-of-the-art audio solutions designed to enhance communication in professional environments. These advanced conferencing systems focus on delivering clear, high-quality audio, ensuring seamless collaboration for users across various sectors including corporate, education, and healthcare.

At the heart of both the COMM 600 and COMM 900 systems is their use of advanced audio technologies. One of the main features is the proprietary AEC (Acoustic Echo Cancellation) and noise reduction technology. This ensures that conversations are free from distractions and interference, allowing for natural communication flow. The systems are equipped with multiple microphones that utilize beamforming technology, which focuses on the person speaking while filtering out background noise. This enhances audio capture, making it ideal for large conference rooms or open office spaces.

Both models support a range of connectivity options, including USB, Bluetooth, and traditional analog inputs. This versatility allows users to connect seamlessly with various devices such as laptops, tablets, and smartphones. The COMM 900 specifically extends these capabilities with support for high-definition video conferencing, making it a comprehensive solution for organizations looking to integrate video alongside audio in their meetings.

Another noteworthy characteristic of these systems is their ease of installation and user-friendly interface. ClearOne has designed the COMM 600 and 900 interfaces to be intuitive, allowing users to set up and operate the systems with minimal technical knowledge. Additionally, integration with popular conferencing platforms is straightforward, further simplifying the user experience.

The scalability of ClearOne’s COMM series is also a significant advantage. Businesses can start with a smaller configuration and easily expand by adding more microphones or integrating additional technologies as their needs grow. This adaptability makes the COMM 600 and COMM 900 ideal for environments that may evolve over time.

In conclusion, the ClearOne COMM 600 and 900 series offers robust audio solutions designed for modern communication needs. With their advanced sound technologies, versatile connectivity options, and user-friendly interfaces, these systems help organizations foster effective collaboration and enhance productivity in any meeting space. Whether for small team discussions or large conferences, ClearOne delivers quality audio performance that supports today’s dynamic communication landscape.