ClearOne comm 600/900 user manual Regional Settings, Telephone Settings

Page 19

 

32

 

RAV-Ware— Configuring System Settings

To change the User Name and Password

1.In the Networking tab, click User/Password.

2.Specify the User name.

3.Type the Password.

4.Retype the password to confirm.

5.Click OK to save changes and close the window.

Note: This option is only available when you are

Figure 3.10. User name/Password

connected to a RAV unit.

To configure the Camera port

1.In the Serial tab, set the Baud Rate to match the baud rate indicated in the camera specifications.

2.Select Flow Control to enable hardware flow control.

3.Click OK to save settings and close the window.

To configure the Control port

1.

Set the Control Port Baud Rate to match the baud

 

 

rate of the PC COM port or the control device.

Figure 3.11. Serial settings

2.

Select Flow Control to enable hardware flow

 

 

control. (Flow Control is selected as default.)

 

3.

Click OK to save settings and close the window.

 

Note: Flow Control is the regulation of information between two devices that are connected to one another. ClearOne recommends enabling Flow Control on the RAV system.

RAV-Ware— Configuring System Settings

 

33

 

Regional Settings

In the Regional Settings window, you can configure the date and time to ensure an accurate time stamp on log files.

To open Regional Settings

•Click the Regional Settings icon in the Configuration screen.

To set date and time

1.Select Use Local Time if you want to use the time on your local computer.

– Or –

Clear the Use Local Time checkbox and enter the IP address for the time server.

2.Select Use Daylight Savings if your region observes daylight savings time.

3.Select your Time Zone and click OK.

4.Click Yes to confirm changes.

Figure 3.13. Date/Time settings

Telephone Settings

In the Telephone Settings window you can set telephone preferences such as auto-answer, auto-disconnect, ringer melody and program the local number. You can also adjust the telco level control, country setting and the flash settings.

!

Attention: If you are connected to the RAV unit through the serial port, you will need to reboot the unit before the baud rate and flow control changes take place. If you are connected to the RAV unit through the USB port, changes are made instantly.

To open Telephone Settings

•Click the Telephone Settings icon in the Configuration screen.

To change RF frequency channel

1.In the Frequency tab, select a frequency.

2.Click OK to save settings and close the window

Note: The channel frequency allows the mixer to communicate with the controller. The frequency used by RAV-Ware must match the frequency used by the controller. See page 58 to set the controller frequency.

!Attention: If you are using the European or South African version of RAV Frequency 1 and Frequency 8 are the same frequency.

Figure 3.12. Frequency settings

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Page Table of Contents Introduction Unpacking Services and supportRAV 600/900 Product returnsRF Radio Frequency Controller Product OverviewMixer Speakers ceiling- or wall-mount Microphone PodsBasic Room Design Basic Room Design for RAVInstallation Overview Network Information System Requirements for RAV-WareWindows 98 SE Connecting the RAV Audio conferencing To set up audio conferencingConnecting the RAV Basic Connections Basic ConnectionsAttach external antenna Insert four AAA batteries into the RF controllerTo connect to a sound card Connecting video codecs, amplifiers and sound cardsAuxiliary Devices To connect to a video codecConnecting for USB control Connecting VCRs and DVD playersConnecting PTZ cameras Connecting for serial controlTo connect to a digital phone Digital phonesRAV-Ware Software Configuration RAV-Ware overview Install RAV-WareIntroduction Getting started with RAV-WareRAV-Ware files RAV-Ware connectionsCommunication Settings Configuring System SettingsNetwork Find Telephone Settings Regional SettingsMicrophones Customizing RAV ComponentsMixer Console Effects of using an external amplifierAdjusting Line Input/Output settings Preconfigured video codecs, amplifiers and sound cardsLine Input and Output Preconfigured record/playback devices Adjusting Record/Playback settingsRecord and Playback Phonebook Setting camera presetsCamera Controls Dialer and Phonebook UsageDialer System Checks Advanced FeaturesEvent Log Firmware upgrades Error MessagesDevice Toolbox Editor Using the RAV Managing Calls Using the ControllerProgramming Phone Preferences Using the Phonebook from the RF ControllerAccessing the menu To delete a Phonebook entry To access the menuConfiguration Adjusting the SettingsTo change LCD contrast To select a frequencyTo perform RF radio test To enter flash durationTo check the RAV version Select Exit to return to the Configuration windowDisplay Select Exit to return to the Configuration window To view the IP addressWeb Interface To connect to RAV through the web interface Accessing the web interfaceOverview DialTo clear log To open event logTo download log Click Yes, Log Out System CheckLog Out To open the system checksAppendix Controller MaintenanceTroubleshooting AudioGeneral SpeakersPinouts Camera pinoutsSpecifications Type and device IDs Command structureConventions Groups and channelsRAV serial commands Serial command error codesMeter type definitions Aarings Number of Rings to Auto Answer On AA Auto Answer Enable/ DisableName Type Size Values Units Aconn Audible Connect / Disconnect Indication AD Auto Disconnect Enable/ DisableAEC Acoustic Echo Canceller enable/ disable Aecref Acoustic Echo Cancellation ReferenceCalldur Call Duration Batterylvl Battery LevelCamctrlmode Camera Control Port Mode Baud Baud RateCammove Move the Camera Campreset Camera PresetCampresetset Camera Preset Setup Camflow Camera Control Flow ControlCamtrack Camera Track CAMPRESETSET2 Camera Preset SetupCamswitchlag Camera Switch Time Lag Camposition Camera PositionCountry Country Selection Default Default The UnitCleareffect Clear Effect Wide Band Telco Emulation Clock Clock SetDial Dtmf Dialing Device Device Identification LabelDid Device ID Enetdnsa Ethernet DNS Server addresses Enetgate Ethernet default Gateway addressEnetaddr Ethernet port IP address Enetdhcp Ethernet Dhcp SelectionFlow Flow Control Eqsel Equalization EnableGain Gain Adjustment EQ EqualizationLabel Label Greport Gate ReportHook Hook Flash Hookd Hook Flash DurationManufacturer Manufacturer Identification Label Lvlreporten Level Report EnableLVL Level Lvlreport Level ReportMute Mute Miccampreset Mic Camera PresetNcsel Noise Cancellation Select Mtrx Matrix RoutingPhonebookdel Deletes an Entry to the Phonebook Pbdial Dial a PB Entry by NamePhonebookadd Adds an Entry to the Phonebook Phonebookcnt Queries the Number of Entries in the PhonebookRing Ring Indication Reset ResetRedial Dial the last number again Rffreq RF Frequency SelectionRingertest Audible Ring Melody Test Silenceprst Silence Camera PresetRingerlvl Audible Ring Level Ringersel Audible Ring Melody SelectionSyschecks System Checks Stereomix Sets the Input to be a Stereo MixSysresult System Check Result UID Unit ID TE Telco EnableTelcolvlctrl Telco TX Level Control Enable/ Disable Volume Volume AdjustmentFCC Part 68 Compliance Electrical Safety AdvisoryCompliance FCC Part 15/ICES-003 ComplianceEuropean Compliance New Zealand ComplianceEC Declaration of Conformity Index

600/900 specifications

ClearOne’s COMM 600 and COMM 900 series are state-of-the-art audio solutions designed to enhance communication in professional environments. These advanced conferencing systems focus on delivering clear, high-quality audio, ensuring seamless collaboration for users across various sectors including corporate, education, and healthcare.

At the heart of both the COMM 600 and COMM 900 systems is their use of advanced audio technologies. One of the main features is the proprietary AEC (Acoustic Echo Cancellation) and noise reduction technology. This ensures that conversations are free from distractions and interference, allowing for natural communication flow. The systems are equipped with multiple microphones that utilize beamforming technology, which focuses on the person speaking while filtering out background noise. This enhances audio capture, making it ideal for large conference rooms or open office spaces.

Both models support a range of connectivity options, including USB, Bluetooth, and traditional analog inputs. This versatility allows users to connect seamlessly with various devices such as laptops, tablets, and smartphones. The COMM 900 specifically extends these capabilities with support for high-definition video conferencing, making it a comprehensive solution for organizations looking to integrate video alongside audio in their meetings.

Another noteworthy characteristic of these systems is their ease of installation and user-friendly interface. ClearOne has designed the COMM 600 and 900 interfaces to be intuitive, allowing users to set up and operate the systems with minimal technical knowledge. Additionally, integration with popular conferencing platforms is straightforward, further simplifying the user experience.

The scalability of ClearOne’s COMM series is also a significant advantage. Businesses can start with a smaller configuration and easily expand by adding more microphones or integrating additional technologies as their needs grow. This adaptability makes the COMM 600 and COMM 900 ideal for environments that may evolve over time.

In conclusion, the ClearOne COMM 600 and 900 series offers robust audio solutions designed for modern communication needs. With their advanced sound technologies, versatile connectivity options, and user-friendly interfaces, these systems help organizations foster effective collaboration and enhance productivity in any meeting space. Whether for small team discussions or large conferences, ClearOne delivers quality audio performance that supports today’s dynamic communication landscape.
Top Page Image Contents