ClearOne comm 600/900 Auxiliary Devices, Connecting video codecs, amplifiers and sound cards

Page 12

18

Connecting the RAV— Auxiliary Devices

Auxiliary Devices

The mixer allows connection to a number of different audio and video peripherals, such as video codecs, VCRs, cameras and computers.

Connecting video codecs, amplifiers and sound cards

Line input/output devices such as video codecs, amplifiers and sound cards can be connected to the Line In or Line Out connectors on the RAV mixer. These connectors provide mono-audio.

To connect to a video codec

1.Using an RCA cable, connect the Line In on the RAV mixer to the line out on a video codec.

2.Using an RCA cable, connect the Line Out on the RAV mixer to the line in on a video codec.

LINE

IN

OUT

Figure 2.11. Connecting a Line In/Out device

Connecting the RAV— Auxiliary Devices

 

19

 

To connect to a sound card

1.Using an RCA cable, connect the Line In on the RAV mixer to the line out on a sound card.

2.Using an RCA cable, connect the Line Out on the RAV mixer to the line in on a sound card.

LINE

IN

OUT

Figure 2.12. Connecting a sound card

To connect to amplifier

Using an RCA cable, connect the Line Out on the RAV mixer to the line in on an amplifier.

LINE

IN

ROUT

Figure 2.13. Connecting an amplifier

Note: Use RAV-Ware to adjust the equalization and volume of these devices. Refer to pages 38–42 for more information. When using RAV-Ware, be sure to drag the amplifier to the cor- rect device (either line out or record). This will properly assign the reference and change the volume command on the controller to control the external amplifier volume.

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Image 12
Contents Page Table of Contents Introduction Services and support RAV 600/900Product returns UnpackingProduct Overview RF Radio Frequency ControllerMixer Microphone Pods Basic Room DesignBasic Room Design for RAV Speakers ceiling- or wall-mountInstallation Overview System Requirements for RAV-Ware Network InformationWindows 98 SE Connecting the RAV To set up audio conferencing Connecting the RAV Basic ConnectionsBasic Connections Audio conferencingInsert four AAA batteries into the RF controller Attach external antennaConnecting video codecs, amplifiers and sound cards Auxiliary DevicesTo connect to a video codec To connect to a sound cardConnecting VCRs and DVD players Connecting PTZ camerasConnecting for serial control Connecting for USB controlDigital phones To connect to a digital phoneRAV-Ware Software Configuration Install RAV-Ware IntroductionGetting started with RAV-Ware RAV-Ware overviewRAV-Ware connections RAV-Ware filesConfiguring System Settings Communication SettingsNetwork Find Regional Settings Telephone SettingsCustomizing RAV Components MicrophonesEffects of using an external amplifier Mixer ConsolePreconfigured video codecs, amplifiers and sound cards Adjusting Line Input/Output settingsLine Input and Output Adjusting Record/Playback settings Preconfigured record/playback devicesRecord and Playback Setting camera presets Camera ControlsDialer and Phonebook Usage PhonebookDialer Advanced Features System ChecksEvent Log Error Messages Firmware upgradesDevice Toolbox Editor Using the RAV Using the Controller Managing CallsUsing the Phonebook from the RF Controller Accessing the menuTo delete a Phonebook entry To access the menu Programming Phone PreferencesAdjusting the Settings ConfigurationTo select a frequency To perform RF radio testTo enter flash duration To change LCD contrastSelect Exit to return to the Configuration window Display Select Exit to return to the Configuration windowTo view the IP address To check the RAV versionWeb Interface Accessing the web interface OverviewDial To connect to RAV through the web interfaceTo open event log To clear logTo download log System Check Log OutTo open the system checks Click Yes, Log OutAppendix Maintenance TroubleshootingAudio ControllerSpeakers PinoutsCamera pinouts GeneralSpecifications Command structure ConventionsGroups and channels Type and device IDsSerial command error codes RAV serial commandsMeter type definitions AA Auto Answer Enable/ Disable Aarings Number of Rings to Auto Answer OnName Type Size Values Units AD Auto Disconnect Enable/ Disable AEC Acoustic Echo Canceller enable/ disableAecref Acoustic Echo Cancellation Reference Aconn Audible Connect / Disconnect IndicationBatterylvl Battery Level Camctrlmode Camera Control Port ModeBaud Baud Rate Calldur Call DurationCampreset Camera Preset Campresetset Camera Preset SetupCamflow Camera Control Flow Control Cammove Move the CameraCAMPRESETSET2 Camera Preset Setup Camswitchlag Camera Switch Time LagCamposition Camera Position Camtrack Camera TrackDefault Default The Unit Cleareffect Clear Effect Wide Band Telco EmulationClock Clock Set Country Country SelectionDevice Device Identification Label Dial Dtmf DialingDid Device ID Enetgate Ethernet default Gateway address Enetaddr Ethernet port IP addressEnetdhcp Ethernet Dhcp Selection Enetdnsa Ethernet DNS Server addressesEqsel Equalization Enable Gain Gain AdjustmentEQ Equalization Flow Flow ControlGreport Gate Report Hook Hook FlashHookd Hook Flash Duration Label LabelLvlreporten Level Report Enable LVL LevelLvlreport Level Report Manufacturer Manufacturer Identification LabelMiccampreset Mic Camera Preset Ncsel Noise Cancellation SelectMtrx Matrix Routing Mute MutePbdial Dial a PB Entry by Name Phonebookadd Adds an Entry to the PhonebookPhonebookcnt Queries the Number of Entries in the Phonebook Phonebookdel Deletes an Entry to the PhonebookReset Reset Redial Dial the last number againRffreq RF Frequency Selection Ring Ring IndicationSilenceprst Silence Camera Preset Ringerlvl Audible Ring LevelRingersel Audible Ring Melody Selection Ringertest Audible Ring Melody TestStereomix Sets the Input to be a Stereo Mix Syschecks System ChecksSysresult System Check Result TE Telco Enable Telcolvlctrl Telco TX Level Control Enable/ DisableVolume Volume Adjustment UID Unit IDElectrical Safety Advisory ComplianceFCC Part 15/ICES-003 Compliance FCC Part 68 ComplianceNew Zealand Compliance European ComplianceEC Declaration of Conformity Index

600/900 specifications

ClearOne’s COMM 600 and COMM 900 series are state-of-the-art audio solutions designed to enhance communication in professional environments. These advanced conferencing systems focus on delivering clear, high-quality audio, ensuring seamless collaboration for users across various sectors including corporate, education, and healthcare.

At the heart of both the COMM 600 and COMM 900 systems is their use of advanced audio technologies. One of the main features is the proprietary AEC (Acoustic Echo Cancellation) and noise reduction technology. This ensures that conversations are free from distractions and interference, allowing for natural communication flow. The systems are equipped with multiple microphones that utilize beamforming technology, which focuses on the person speaking while filtering out background noise. This enhances audio capture, making it ideal for large conference rooms or open office spaces.

Both models support a range of connectivity options, including USB, Bluetooth, and traditional analog inputs. This versatility allows users to connect seamlessly with various devices such as laptops, tablets, and smartphones. The COMM 900 specifically extends these capabilities with support for high-definition video conferencing, making it a comprehensive solution for organizations looking to integrate video alongside audio in their meetings.

Another noteworthy characteristic of these systems is their ease of installation and user-friendly interface. ClearOne has designed the COMM 600 and 900 interfaces to be intuitive, allowing users to set up and operate the systems with minimal technical knowledge. Additionally, integration with popular conferencing platforms is straightforward, further simplifying the user experience.

The scalability of ClearOne’s COMM series is also a significant advantage. Businesses can start with a smaller configuration and easily expand by adding more microphones or integrating additional technologies as their needs grow. This adaptability makes the COMM 600 and COMM 900 ideal for environments that may evolve over time.

In conclusion, the ClearOne COMM 600 and 900 series offers robust audio solutions designed for modern communication needs. With their advanced sound technologies, versatile connectivity options, and user-friendly interfaces, these systems help organizations foster effective collaboration and enhance productivity in any meeting space. Whether for small team discussions or large conferences, ClearOne delivers quality audio performance that supports today’s dynamic communication landscape.