ClearOne comm 600/900 user manual Speakers, Pinouts, Camera pinouts, General

Page 40

74

Appendix — Troubleshooting

Speakers

Neither speakers play

Check that the wires are properly connected. Check the audio mixer in RAV-Ware to ensure the audio is routed to the loudspeakers.

Bass and treble are weak

Check the equalization for the loudspeakers in RAV-Ware.

Only one speaker plays

Check the equalization for the loudspeakers in RAV-Ware. Check the wires connected to the speaker that does not play. Be sure the wires are in good condition and are firmly connected.

Appendix— Pinouts

 

75

 

Pinouts

Camera pinouts

8-Pin Mini DIN connector

Pin Number

Control

Pin Number

Control

1

RTS

5

RXD

2

CTS

6

TXD

3

TXD

7

not used

4

GND

8

not used

 

8 Pin Mini DIN

 

8 Pin Mini DIN

One speaker still does not play

Disconnect the wires from both the speaker and the mixer. Disconnect the other wire from its speaker and connect that end of the wire to the speaker that doesn't play. If the speaker still doesn't play, the problem is in the speaker. If the speaker now plays, continue checking for the source of the problem. Disconnect the same wire from the mixer. Connect it to another output. If the speaker plays, the problem is the original wire that was connected to that speaker.

General

Pin 1 RTS

Pin 2 CTS

Pin 3 TXD

Pin 4 GND

Pin 5 RXD

Pin 6 TXD not used Pin 7 Not used Pin 8 Not used

Pin 2 CTS

Pin 1 RTS

Pin 5 RXD

Pin 4 GND

Pin 3 TXD

Pin 6 GND not used Pin 7 Not used Pin 8 Not used

Physical damage to RAV

All repairs must be done by a ClearOne technician. Call ClearOne technical support for more information.

DB-9 connector

Pin Number

Control

Pin Number

Control

 

1

CD

6

DSR

 

2

RXD

7

RTS

 

3

TXD

8

CTS

 

4

DTR

9

RI

 

 

DB-9

 

8 Pin Mini DIN

 

 

 

 

 

 

 

 

Pin 1

CD

 

Pin 2 CTS

 

 

Pin 2 RXD

 

Pin 3 TXD

 

 

Pin 3 TXD

 

Pin 5 RXD

 

 

Pin 4 DTR

 

 

 

 

 

Pin 5 GND

 

Pin 4 GND

 

 

Pin 6 DSR

 

 

 

 

 

Pin 7

RTS

 

Pin 2 CTS

 

 

Pin 8

CTS

 

Pin 1

RTS

 

 

Pin 9

RI

 

Pin 6

GND Not used

 

 

 

 

 

Pin 7

Not used

 

 

 

 

 

 

 

 

 

 

Pin 8

Not used

 

 

 

 

 

 

 

 

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Image 40
Contents Page Table of Contents Introduction Services and support RAV 600/900Product returns UnpackingRF Radio Frequency Controller Product OverviewMixer Microphone Pods Basic Room DesignBasic Room Design for RAV Speakers ceiling- or wall-mountInstallation Overview Network Information System Requirements for RAV-WareWindows 98 SE Connecting the RAV To set up audio conferencing Connecting the RAV Basic ConnectionsBasic Connections Audio conferencingInsert four AAA batteries into the RF controller Attach external antennaConnecting video codecs, amplifiers and sound cards Auxiliary DevicesTo connect to a video codec To connect to a sound cardConnecting VCRs and DVD players Connecting PTZ camerasConnecting for serial control Connecting for USB controlDigital phones To connect to a digital phoneRAV-Ware Software Configuration Install RAV-Ware IntroductionGetting started with RAV-Ware RAV-Ware overviewRAV-Ware connections RAV-Ware filesCommunication Settings Configuring System SettingsNetwork Find Regional Settings Telephone SettingsCustomizing RAV Components MicrophonesEffects of using an external amplifier Mixer ConsoleAdjusting Line Input/Output settings Preconfigured video codecs, amplifiers and sound cardsLine Input and Output Preconfigured record/playback devices Adjusting Record/Playback settingsRecord and Playback Setting camera presets Camera ControlsDialer and Phonebook Usage PhonebookDialer System Checks Advanced FeaturesEvent Log Firmware upgrades Error MessagesDevice Toolbox Editor Using the RAV Using the Controller Managing CallsUsing the Phonebook from the RF Controller Accessing the menuTo delete a Phonebook entry To access the menu Programming Phone PreferencesAdjusting the Settings ConfigurationTo select a frequency To perform RF radio testTo enter flash duration To change LCD contrastSelect Exit to return to the Configuration window Display Select Exit to return to the Configuration windowTo view the IP address To check the RAV versionWeb Interface Accessing the web interface OverviewDial To connect to RAV through the web interfaceTo clear log To open event logTo download log System Check Log OutTo open the system checks Click Yes, Log OutAppendix Maintenance TroubleshootingAudio ControllerSpeakers PinoutsCamera pinouts GeneralSpecifications Command structure ConventionsGroups and channels Type and device IDsRAV serial commands Serial command error codesMeter type definitions Aarings Number of Rings to Auto Answer On AA Auto Answer Enable/ DisableName Type Size Values Units AD Auto Disconnect Enable/ Disable AEC Acoustic Echo Canceller enable/ disableAecref Acoustic Echo Cancellation Reference Aconn Audible Connect / Disconnect IndicationBatterylvl Battery Level Camctrlmode Camera Control Port ModeBaud Baud Rate Calldur Call DurationCampreset Camera Preset Campresetset Camera Preset SetupCamflow Camera Control Flow Control Cammove Move the CameraCAMPRESETSET2 Camera Preset Setup Camswitchlag Camera Switch Time LagCamposition Camera Position Camtrack Camera TrackDefault Default The Unit Cleareffect Clear Effect Wide Band Telco EmulationClock Clock Set Country Country SelectionDial Dtmf Dialing Device Device Identification LabelDid Device ID Enetgate Ethernet default Gateway address Enetaddr Ethernet port IP addressEnetdhcp Ethernet Dhcp Selection Enetdnsa Ethernet DNS Server addressesEqsel Equalization Enable Gain Gain AdjustmentEQ Equalization Flow Flow ControlGreport Gate Report Hook Hook FlashHookd Hook Flash Duration Label LabelLvlreporten Level Report Enable LVL LevelLvlreport Level Report Manufacturer Manufacturer Identification LabelMiccampreset Mic Camera Preset Ncsel Noise Cancellation SelectMtrx Matrix Routing Mute MutePbdial Dial a PB Entry by Name Phonebookadd Adds an Entry to the PhonebookPhonebookcnt Queries the Number of Entries in the Phonebook Phonebookdel Deletes an Entry to the PhonebookReset Reset Redial Dial the last number againRffreq RF Frequency Selection Ring Ring IndicationSilenceprst Silence Camera Preset Ringerlvl Audible Ring LevelRingersel Audible Ring Melody Selection Ringertest Audible Ring Melody TestSyschecks System Checks Stereomix Sets the Input to be a Stereo MixSysresult System Check Result TE Telco Enable Telcolvlctrl Telco TX Level Control Enable/ DisableVolume Volume Adjustment UID Unit IDElectrical Safety Advisory ComplianceFCC Part 15/ICES-003 Compliance FCC Part 68 ComplianceEuropean Compliance New Zealand ComplianceEC Declaration of Conformity Index

600/900 specifications

ClearOne’s COMM 600 and COMM 900 series are state-of-the-art audio solutions designed to enhance communication in professional environments. These advanced conferencing systems focus on delivering clear, high-quality audio, ensuring seamless collaboration for users across various sectors including corporate, education, and healthcare.

At the heart of both the COMM 600 and COMM 900 systems is their use of advanced audio technologies. One of the main features is the proprietary AEC (Acoustic Echo Cancellation) and noise reduction technology. This ensures that conversations are free from distractions and interference, allowing for natural communication flow. The systems are equipped with multiple microphones that utilize beamforming technology, which focuses on the person speaking while filtering out background noise. This enhances audio capture, making it ideal for large conference rooms or open office spaces.

Both models support a range of connectivity options, including USB, Bluetooth, and traditional analog inputs. This versatility allows users to connect seamlessly with various devices such as laptops, tablets, and smartphones. The COMM 900 specifically extends these capabilities with support for high-definition video conferencing, making it a comprehensive solution for organizations looking to integrate video alongside audio in their meetings.

Another noteworthy characteristic of these systems is their ease of installation and user-friendly interface. ClearOne has designed the COMM 600 and 900 interfaces to be intuitive, allowing users to set up and operate the systems with minimal technical knowledge. Additionally, integration with popular conferencing platforms is straightforward, further simplifying the user experience.

The scalability of ClearOne’s COMM series is also a significant advantage. Businesses can start with a smaller configuration and easily expand by adding more microphones or integrating additional technologies as their needs grow. This adaptability makes the COMM 600 and COMM 900 ideal for environments that may evolve over time.

In conclusion, the ClearOne COMM 600 and 900 series offers robust audio solutions designed for modern communication needs. With their advanced sound technologies, versatile connectivity options, and user-friendly interfaces, these systems help organizations foster effective collaboration and enhance productivity in any meeting space. Whether for small team discussions or large conferences, ClearOne delivers quality audio performance that supports today’s dynamic communication landscape.