Weslo WCTL35090 user manual Maintenance and TROUBLE-SHOOTING, Cord

Page 13

MAINTENANCE AND TROUBLE-SHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please call our Customer Service Department toll-

free at 1-888-936-4266, Monday through Friday, 8 a.m. until 6:30 p.m. Eastern Standard Time (excluding holidays).

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge protector, and that the surge protector is plugged into a properly grounded outlet. (See HOW TO PLUG IN THE POWER CORD on page

8.) Use only a CUL-listed surge protector, rated at 15 amps, with a 14-gauge cord of five feet or less in length.

b. After the power cord has been plugged in, make sure that the key is fully inserted into the con- sole. See step 1 on page 9.

c. Check the circuit breaker located on the treadmill frame near the power cord. If the switch pro- trudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

PROBLEM: The power turns off during use

c

Tripped

Reset

SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in.

c. Remove the key from the console. Reinsert the key fully into the console. See step 1 on page 9.

d. If the treadmill still will not run, please call our Customer Service Department, toll-free.

PROBLEM: The displays of the console do not function properly

SOLUTION: a. Check the batteries in the console. If the batteries need to be replaced, see BATTERY INSTALLATION on page 9. Most problems are the result of drained batteries.

b. First remove the key and

UNPLUG THE POWER

CORD

. Remove the screws from the hood.

Carefully remove the hood. Locate the Reed Switch

(63)and the Magnet (65) on the left side of the Pulley (68). Turn the Pulley until the Magnet is

aligned with the Reed Switch. Make sure that the

gap between the Magnet and the Reed Switch is

about 1/8”. If necessary, loosen the Screw (24) and move the Reed Switch slightly. Retighten the Screw.

Re-attach the hood, and run the treadmill for a few minutes to check for a correct speed reading.

24

63

1/8”

Top View

68

65

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents QUESTIONS? Customer ServiceModel No. WCTL35090 Serial No Serial Number DecalTable of Contents Important Precautions Erty damage sustained by or through the use of this product For your benefit, read this manual carefully before Before YOU BeginFront BackAssembly Yet Right HandrailRight Upright 31. Do not tighten the Bolt yet Make sure that all parts are tight before you useOperation and Adjustment Battery Installation Diagram of the ConsoleStep by Step Console Operation Reset position Reset the console and start the walking belt Can be restarted Follow your progress with the three displaysHOW to Change the Incline Treadmill HOW to Fold and Move the TreadmillHOW to Select Kilometres and Miles HOW to Fold the Treadmill for StorageHOW to Lower the Treadmill for USE HOW to Move the TreadmillStorage latch locks over the frame guide To protect the floor or carpet from damage, place aCord Maintenance and TROUBLE-SHOOTINGProblem The walking belt slows when walked on SolutionIf the walking belt has shifted to the left Exercise Intensity Conditioning GuidelinesWorkout Guidelines Exercise FrequencySuggested Stretches Page Model No Serial No Customer RecordDate AddressDe l’Industrie St-Jérôme, Québec Canada, J7Y 4B8 Ordering Replacement PartsIcon of CANADA, 900 de l’Industrie, St. Jérôme, QC J7Y 4B8 Limited WarrantyPart No J02204-C R0602A Remove this Exploded Drawing and Part List from the Manual Qty Description Part LIST-Model No. WCTL35090R0602A Exploded DRAWING-Model
Top Page Image Contents