Star Trac E-TCI, NOT FOUND manual Adjustments

Page 51

Adjustments

The running belt and its headroller, drive belt, tailroller, and running deck are designed to be self-centering, slip-free, and smooth-oper- ating without the need for frequent adjustments. Running belt sideward movement, slipping, or grinding after extended use, or thump-ing during initial use, may be corrected by the following procedures. Note, each belt must be adjusted separately:

Adjust TRACKING: If the running belt is not centered on the tailroller and is either too far left or right, adjust tracking using the follow- ing steps:

1. Turn the TreadClimber® on. Increase TreadClimber speed to 3.0 mph (5.0 km/h).

RUNNING BELT

2. Adjust tracking by turning the left Allen screws (located at the front side of the head roller) with a 1/4" Allen wrench in 1/4-turn increments.

If the running belt is tracking to the left, turn the screws clock-wise in 1/4 turn increments.

If the running belt is tracking to the right, turn the left screw counter- clockwise in 1/4 turn increments.

3.NOTE: ONLY USE THE LEFT SCREW FOR TRACKING ADJUSTMENT.

4.After the running belt appears to be tracking properly, increase the TreadClimber by STAR TRAC speed to 4.0 mph (6.7 km/h) and verify that the belt stays centered.

Slipping-Running Belt: Remove the motor shroud and operate the treadmill slowly at 1 to 2 mph (2 to 3 km/h). While observing the tailroller, walk on the belt and try to slow it down by gently applying pressure with your feet while holding the handrails. If only the run- ning belt, and not the tailroller, slows down, tighten the running belt by turning both the right and left tailroller adjustment bolts clock- wise 1/4-turn. Repeat this adjustment until the running belt no longer slips, ensuring that you turn both tailroller bolts an equal number of turns. Re-install the motor shroud. If the headroller and the running belt both slow down, tighten the drive belt as described under “Slipping-Drive Belt”, below.

Slipping Drive Belt: The drive belt tensioning system is designed for minimal adjustment throughout the life of the belt. To check if the drive belt tension needs to be adjusted, do the following:

1.Run TreadClimber at 2 mph (3km/h) and try and stop the belt by applying foot pressure while holding onto the handrails. If the running belt and roller stop, but the motor continues to turn, the drive belt tension needs adjustment.

2.Remove the motor shroud.

3.Release belt tension by releasing the belt tensioner.

4.Move the spring to the second hole on the tensioner swing arm.

5.Re-tension with the tensioner.

6.Reinstall motor shroud.

TOOLS & MATERIALS

Clean Towel (1)

Paint Stick or Ruler (1)

Diluted All-purpose Cleaner (409), or Bristle Brush

TREADCLIMBER by STAR TRAC - OWNER’S MANUAL Operating Instructions 51

Image 51
Contents TreadClimber Page Table Of Contents Customer Support ManufacturerImportant Safety Instructions Safety InstructionsStop of Action Alternating Current OFF Do notPage DOE DIT Niet VeiligheidsinstructiesWaarschuwing DOE DIT WELPage Arrêt Mise Hors Service Courant Alternatif Ouvre Ferme Mesures DE PrecautionSicherheitsvorschriften WarnungBedienung Unterbrechen Wechselstrom EIN AUS SIE Sollten SIE Sollten NiemalsLesen SIE Alle Anweisungen VOR DER Benutzung DEL Laufbandes Leggete Tutte LE Istruzioni Prima DI Usare IL Treadclimber Istruzioni DI SicurezzaAttenzione Ferma IL Movimento Corrente Alternata Acceso SpentoDafare DA NON FareStartrac Leia Todas AS Instruções Antes DE Usar SUA Esteira Instruções DE SegurançaAdvertência Pare a Ação Corrente Alternada Ligar DesligarPage Apagado Instrucciones DE SeguridadAdvertencia Parar EL Functionamiento Corriente AlternaPage Stop AF Funktion Vekselstrøm Tænd Sluk SikkerhedsinstruktionerSkal MÅ IkkePage Unpacking & Parts List Assembly & SetupAssembly Instructions Final Torque In-Lbs 4.0 Nm Final Torque Final Torque Page Page Page Page Page Operating Instructions Display Control Panel Features Mets Pull Cord Stop HOT BAR Control FeaturesHints and Tips for Getting Started To operate the Quick Start program Quick StartDistance Preset ProgramsHeartRateTraining Programs Using the Cooling Fan Cooldown CycleHeart Rate Monitoring Contact Heart Rate Monitoring Manager Mode Settings & TestingLanguage Maintenance ModeSerial no WeightMC1 V LCB VLockout ID Test ErrorLast Error Mode CCB V USB VMotor Calibration Troubleshooting FCC and Other Domestic / International Regulations Regulatory InformationEFT ESDMonthly Maintenance MaintenanceDaily Maintenance Weekly MaintenanceAdjustments Corporate Headquarters