NordicTrack NTL11806.1 manual

Page 9

5.Identify the Latch Assembly (76). Make sure that the sleeve has been slid over hole 1 and that the latch knob is locked into hole 1. Pull on the sleeve to make sure that it is locked into place.

Next, make sure that the latch knob is locked into hole 2. If it is not, pull out the tube until you see hole 2 and then slide the tube back in until the latch knob locks into hole 2.

6.Raise the Frame (55) to the position shown. Have a second person hold the Frame until this step is completed.

Remove the plastic ties from the ends of the Latch Assembly (76). Orient the Latch Assembly so that the large barrel and the knob are in the positions shown; make sure that all the holes are aligned as shown in the inset drawings. Attach the lower end of the Latch Assembly to the bracket in the center of the Uprights (85) with a Latch Bolt (109) and a Nut (20).

Attach the upper end of the Latch Assembly (76) to the bracket on the Frame (55) with a Latch Bolt (109) and a Nut (20). Note: It may be neces- sary to move the Frame back and forth to align the Latch Assembly with the bracket.

Lower the Frame (55) (see HOW TO LOWER THE TREADMILL FOR USE on page 28).

7.Identify the Left Base Cover (88), which has cutouts in the locations shown. Slide the Left Base Cover onto the left Upright (85). Then, slide the Right Base Cover (86) onto the right Upright.

Identify the Left Upright Sleeve (77) and the Right Upright Sleeve (9). Slide the Upright Sleeves onto the Uprights (85) as shown.

5

Hole 2

Latch Knob

Tube			Hole 1
		Sleeve
			76
6
		55
20		109	Top
		109	Top
		76	Holes
		76
Knob
		Large
		Barrel
		85
			Holes
	20		Bottom
		109	Bottom
		109
7		85
		85
		Left
			Right
		77
Cutouts		88	9
		86
9

Image 9

Contents QUESTIONS? Model No. NTL11806.1 Serial NoCall TOLL-FREE Table of Contents Important Precautions Page Power Lines Service To External Antenna Before YOU Begin Assembly Make sure that the power cord is unpluggedFirmly tighten the Extension Leg Bolts Firmly tighten the Extension Leg Bolts Page Start all four Console Bolts and then tighten Them Not shown. Make sure that no wires are PinchedPage Page HOW to Connect AN External Source Using a Catv Cable HOW to Connect a 75 OHM Catv CableOperation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerMeasure your heart rate if desired Turn on the fan if desiredWhenkey. you are finished exercising, remove Select one of the fourteen preset programs HOW to USE a Preset ProgramIdentify yourself as user 1 or user Press the Start button to start the programSelect one of the four pulse programs HOW to USE a Pulse ProgramTurn on the fan if desired Select one of the four custom programs HOW to Create a Custom ProgramHOW to USE a Custom Program Insert an iFIT Card and select a program HOW to USE AN Ifit CardPress the Volume buttons to adjust the volume HOW to Operate the Personal TelevisionHOW to USE the Stereo Sound System Press the Channel buttons to select Desired channelPress the Power button again and add or re Move channels HOW to USE the Information ModeOptional Chest Pulse Sensor HOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingTop Problem The walking belt slows when walked onProblem Television reception is poor Exercise Intensity Conditioning GuidelinesWorkout Guidelines Exercise FrequencySuggested Stretches Qty Description R1107AOrdering Replacement Parts Drawing a ExplodedExploded Drawing B-Model No. NTL11806.1 Exploded Drawing C-Model No. NTL11806.1 Exploded Drawing D-Model No. NTL11806.1 Limited Warranty