NordicTrack NTL12950 user manual

Page 8

5.Cut the tie securing the Pulse Wire (74) to the Upright Base (85). Hold the Pulse Bar Assembly (69) near the crossbar on the Upright Base (85). Connect the Pulse Wire to the wire in the Pulse Bar Assembly. The connec- tors should slide together easily and snap into place. If they do not, turn one connector and try again. Insert the wires into the crossbar.

Open parts bag B. Attach the Pulse Bar Assembly (69) to the crossbar on the Upright Base (85) with four Pulse Bar Bolts (127) and Star Washers (67). Start all four Pulse Bar Bolts before tightening them. Make sure that no wires are pinched.

If you have purchased an optional chest pulse sensor, follow step 6 to install the receiver included with the chest pulse sensor. If you have not, go to step 7.

6.Place the console assembly face-down. Be careful not to scratch the face of the console. Remove the indicated 3/4” Screw (7) and the Access Door (95) from the left side of the Console Back (96).

Connect the wire on the receiver (A) to the indicated wire extending from the Console Back (96). Hold the receiver so the small cylinder is oriented as shown and is fac- ing the Console Back. Attach the receiver to the plastic posts on the Access Door (95) with the two included small screws.

Make sure that no wires are pinched. Reattach the Access Door (95) with the 3/4” Screw (7). Discard the other wires included with the receiver.

7.Cut the tie securing the wires to the Upright Base (85). Have a second person hold the console assembly near the Upright Base. Connect the Upright Wire Harness (73) and the Pulse Wire (74) to the wires extending from the console assembly. The connectors should slide together easily and snap into place. If they do not, turn one connector and try again. Insert the connectors into the console as- sembly. If necessary, remove the right accessory tray (not shown) from the console assembly.

Connect the Upright Ground Wire (113) to the ground wire extending from the console assembly. Make sure that the wires are fully inserted into each other. Insert the ground wires into the console assembly. Reinsert the right acces- sory tray (not shown) into the console assembly if neces- sary.

5

 

127

 

67

 

85

127

 

67

74

 

69

 

74

 

6

 

7

 

Small

95

 

Cylinder

 

A

96

 

Wire

 

Small

 

Screws

 

7

 

Console

 

Assembly

 

Ground

74

Wire

 

113

73

73

85 74

8

Image 8
Contents Customer HOT Line QUESTIONS?Model No. NTL12950 Serial No Table of Contents Important Precautions Page Before YOU Begin Assembly Page Page Page Wire PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Features of the Console HOW to Turn on the Power HOW to USE the Manual ModeFollow your progress with the display Whenkey. you are finished exercising, remove Measure your heart rate if desiredTurn on the fans if desired Adjust the intensity level of the program if Desired HOW to USE a Preset ProgramSelect one of the preset programs See on HOW to Create a Custom Program Select one of the custom programsHOW to USE a Custom Program Select a heart rate program HOW to USE a Heart Rate ProgramEnter a maximum target heart rate setting Follow your progress with the displays Audio Cable HOW to Connect Your MP3 Player or CD PlayerHOW to Connect Your Portable Stereo HOW to Connect Your Home Stereo HOW to Connect Your ComputerHOW to Connect Your VCR Press the Play button on your MP3 player, CD Player, or VCRMeasure your heart rate if desired Return to the treadmill and stand on the foot Directly from OUR WEB SiteFollow the on-line instructions to start Program Optional Chest Pulse Sensor Information MODE/DEMO ModeHOW to Adjust the Cushioning System HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on TopConditioning Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencySuggested Stretches R1004B Qty DescriptionOrdering Replacement Parts Exploded DRAWING-Model No. NTL12950 R1004B Limited Warranty