Horizon Fitness DT680 manual TENSIONING­THE Running Belt

Page 14

INTRODUCTION IMPORTANT

PRECAUTIONS

ASSEMBLY

BEFORE

YOU BEGIN

TREADMILL

OPERATION

CONDITIONING TROUBLESHOOTING LIMITED

GUIDELINES & MAINTENANCE WARRANTY

13

TENSIONING­THE RUNNING BELT

The running belt has been properly adjusted at the factory before it was shipped. At times the belt can move off-center during shipment.

CAUTION: Running belt should NOT be moving during tensioning. Over-tightening the running belt can cause excessive wear on the treadmill as well as its components. Never over-tighten the belt.

If you can feel a slipping sensation when running on the treadmill, the running belt must be tightened. In most cases, the belt has stretched from use, causing the belt to slip. This is a normal and common adjustment. To eliminate this slipping, turn the treadmill off and tension both the rear roller bolts using the supplied Allen wrench, turning them 1/4 TURN to the right as shown. Turn the treadmill on and check for slipping. Repeat if necessary, but NEVER TURN the roller bolts more than 1/4 turn at a time. Belt is properly tensioned when the slipping sensation is gone.

Belt is too far to the right side

Belt is too far to the left side

CENTERING THE RUNNING BELT

The running belt has been properly adjusted at the factory before it was shipped. At times the belt can move off-center during shipment. Before operating the treadmill, make sure the belt is centered and remains centered to maintain smooth operation.

CAUTION: Do not run belt faster than 1/2 mph while centering. Keep fingers, hair and clothing away from belt at all times.

If the running belt is too far to the right side:

With the treadmill running at 1/2 mph, turn the right adjustment bolt clockwise 1/4 turn at a time (using the supplied Allen wrench). Check the belt alignment. Allow belt to run a full cycle to gauge if more adjustment is needed. Repeat if necessary, until the belt remains centered during use.

If the running belt is too far to the left side:

With the treadmill running at 1/2 mph, turn the right adjustment bolt counter-clockwise 1/4 turn at a time (using the supplied Allen wrench). Check the belt alignment. Allow belt to run a full cycle to gauge if more adjustment is needed. Repeat if necessary, until the belt remains centered during use.

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Treadmill USER’S Guide Page Table of Contents T R O D U C T I O NImportant Precautions Grounding InstructionsOperation Use the treadmill only as described in this manualS E M B LY UnpackingTools Included Parts IncludedE a S S E M B LY Open Hardware BAGUpright masts Pulse wiresPosition, place console Mast and consoleSlide top of Handle BAR into Console MastSupport BAR Console PostAssembly Step YOU’RE FinishedLocation of the Treadmill Safety KEYBefore YOU Begin Here are just a few of the health benefits of exerciseMoving Proper UsageFolding TENSIONING­THE Running Belt Treadmill Operation 10 % MPHPulse Grips Monitor DisplayHeart Rate Clear Current Selection Select a LevelSelect a Time Scan Viewing ScreensO G R a M Hills O G R a M ManualO G R a M Intervals Intervals Program SegmentsO G R a M Weight Loss Program THR Zone Conditioning Guidelines Perceived Exertion LevelTarget Heart Rate Zone Chart ExampleStanding Calve Muscle Stretch StretchingStretch First Standing Quadriceps StretchWarm UP P S Achieving Your Fitness GoalsKeeping AN Exercise Diary Cool DownWeekly LOG Sheets Weekly TotalsWeekly LOG Sheets Monthly LOG Sheets Week # Distance Calories Time Monthly TotalsWhen should I BE Worried about a NOISE? TroubleshootingTroubleshooting Treadmill Common Product QuestionsTroubleshooting Heart Rate I N T E N a N C E After Each USE DailyLimited Home USE Warranty Exclusions and LimitationsCustomer Tech Support
Top Page Image Contents