INTRODUCTION IMPORTANT PRECAUTIONS
P R E - A S S E M B LY
DO NOT ATTEMPT TO LIFT THE TREADMILL!* Do not move or lift treadmill
WARNING from packaging until specified to do so in the assembly instructions. Failure to do so may result in injury! Remove plastic wrap from console masts.
Note: During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before
completely tightening any ONE bolt. NOTE: A light application of grease may aid in the installation of hardware. Any grease, such as lithium bike grease is recommended.
A S S E M B LY STEP 1
A S S E M B LY STEP 2
HARDWARE BAG 2 CONTENTS :
| FLAT WASHER (E) | WAVY WASHER (F) | |
BOLT (D) | 27 mm | 29 mm | |
Qty: 1 | Qty: 1 | ||
Qty: 1 | |||
|
|
LEAD WIRES |
IMPORTANT PRECAUTIONS INTRODUCTION
ASSEMBLY
HARDWARE BAG 1 CONTENTS :
BOLT (A) | FLAT WASHER (B) | TEFLON WASHER (C) |
15 mm | 20 mm | 18 mm |
Qty: 1 | Qty: 1 | Qty: 1 |
BOLT (D) | FLAT WASHER (E) | WAVY WASHER (F) |
Qty: 1 | 27 mm | 29 mm |
| Qty: 1 | Qty: 1 |
| RIGHT CONSOLE MAST |
MAIN FRAME |
|
WAVY WASHER (F) | FLAT WASHER (E) |
RIGHT CONSOLE MAST |
|
ASSEMBLY
BEFORE YOU BEGIN
MAIN FRAME |
LEFT CONSOLE MAST |
WAVY WASHER (F) |
CONSOLE CABLES | BOLT (D) |
| |
| RIGHT LINKAGE ARM |
FOOT LOCK LATCH |
|
ELEVATION FRAME CONSOLE CABLES |
BEFORE YOU BEGIN
TREADMILL OPERATION
CONDITIONING TROUBLESHOOTING LIMITED GUIDELINES & MAINTENANCE WARRANTY
FLAT WASHER (E) |
|
BOLT (D) |
|
LEFT LINKAGE ARM |
|
BOLT (A) |
|
FLAT WASHER (B) |
|
TEFLON WASHER (C) | ELEVATION FRAME |
AOpen HARDWARE BAG 1.
BCut banding straps. Do not move or lift treadmill from packaging.
CMove left linkage arm into position. Insert bolt (A) and FLAT WASHER (B) into left linkage arm followed by a TEFLON washer (C) and attach to elevation frame.
DLift left console mast into upright position. Be sure to hold the console mast firmly, as it will not stay in the upright position on its own.
EInsert bolt (D) and 1 FLAT washer (E) through left console mast followed by a WAVY washer (F) and attach to MAIN FRAME.
A. Pull LEAD WIRE through RIGHT CONSOLE MAST. After pulling the lead wire through the mast, the top of the console cables should be located at the top of the mast. Detach and discard lead wire.
B. Open HARDWARE BAG 2.
C. Move right linkage arm into position and attach to
ELEVATION FRAME.
Note: While holding RIGHT CONSOLE MAST in the upright position, tighten
D. Attach RIGHT CONSOLE MAST to MAIN FRAME using 1 BOLT (D), 1 FLAT WASHER (E) and 1 WAVY WASHER (F).
E. Lift the running deck until lock latch on side of treadmill is fully engaged.
F.Remove console from box and place out of the way.
G.Lower the treadmill running deck from the folded position by stepping on LOCK LATCH on lower right side.
*Note: If you have attempted to move the treadmill from the box and the machine has sprung open and cannot be assembled, refer to the troubleshooting section in order to restore the treadmill to its proper position.
1 |
3 |
2 |
TREADMILL OPERATION
LIMITED TROUBLESHOOTING CONDITIONING WARRANTY & MAINTENANCE GUIDELINES
T83_Treadmill_Rev.1.8.indd | 7/9/07 9:56:00 AM |