Time/Incline/Segment |
|
| ||
Time display |
|
| ||
the manual mode or the |
|
|
| |
iFIT.com mode is se- |
|
|
| |
lected, this display will |
|
| ||
|
| |||
show the elapsed time |
|
|
| |
and the incline level of the treadmill. The display | ||||
will change from one number to the other every | ||||
few seconds, as shown by the indicators in the | ||||
display. When a personal trainer program or a | ||||
heart rate program is selected, the display will | ||||
show the | time remaining | in the program, the time | ||
remaining in the current segment of the program, | ||||
and the incline level. Note: Each time the incline | ||||
changes, the display will show the current incline | ||||
setting for several seconds. |
|
| ||
Distance/Laps |
|
|
| |
|
|
| ||
display |
|
| ||
shows the distance that |
|
| ||
you have walked and the |
|
| ||
number of |
|
| ||
you have completed. The |
|
| ||
display will change from one number to the other | ||||
every few seconds, as shown by the indicators in | ||||
the display. |
|
|
| |
|
|
| ||
|
|
| ||
display |
|
| ||
shows the speed of the |
|
| ||
walking belt and your |
|
| ||
current pace (pace is |
|
| ||
|
| |||
measured in | minutes per |
|
| |
mile ). The display will change from one number to the other every few seconds, as shown by the in- dicators in the display. Note: Each time the speed changes, the display will show the current speed setting for several seconds.
Note: The console can display speed and dis- tance in either miles or kilometers. To find which
unit of measurement is selected, hold down the
Stop button while inserting the key into the con-
sole. An “E” for English miles or an “M” for metric kilometers will appear in the display. Press the
Speed ▲ button to change the unit of measure- ment. When the desired unit of measurement is selected, remove the key and then reinsert it.
To reset the displays, press the Stop button, re- move the key, and then reinsert the key.
6 Measure your heart rate, if desired.
To measure you heart rate, use the chest pulse sensor (see page 10) or the handgrip pulse sen- sor (follow the instructions below). Note: Before using the handgrip pulse sensor, make sure that your hands are clean.
| To measure your |
|
|
| heart rate, | stand |
|
| on the foot rails |
|
|
| and place your |
|
|
| hands on the |
|
|
| metal contacts on |
|
|
| the handrail. Your |
| |
| palms must be |
|
|
| resting on the con- |
| |
| tacts— avoid | moving your hands | . When your |
| pulse is detected, the |
| |
| Calories/Fat Calories/Heart Rate display will flash, | ||
| and then your heart rate will be shown. | For the | |
| most accurate heart rate reading, continue to |
| |
| hold the contacts for about 15 seconds. | The | |
| chest pulse sensor (see page 10) can also be |
| |
| used. |
|
|
7 | key.When you are finished exercising, remove the |
| |
Step onto the foot rails, press the Stop button, and adjust the incline of the treadmill to the lowest setting. The incline must be at the lowest setting when the treadmill is folded to the storage posi-
tion or the treadmill will be damaged.Next, re- move the key from the console and put it in a se-
cure place. Note: If the displays and various indi- cators on the console remain lit after the key is removed, the console is in the “demo” mode.
See page 23 and turn off the demo mode.
When you are finished using the treadmill, move the on/off switch near the power cord to the off position and unplug the power cord.
14