Reebok Fitness RBTL69920 manual 55If. the connectors do not fit together easily, Do not fully

Page 7

4. Locate the Belly Pan Wire Harness (124). Route the Belly

4

58

Pan Wire Harness over the B

ase (117) as shown.

 

55 124

Connect the Belly Pan Wire Harness to the Wire Harness

 

 

(55)If. the connectors do not fit together easily

,rotate

 

them and then connect them.

See the inset drawing.

 

 

Carefully wrap the wires around the connectors as

 

 

shown. Insert the connectors and the excess Wire

 

 

Harness into the Right Upright (58).

 

 

 

With the help of another person, carefully tip the treadmill

 

117

 

 

 

 

 

 

onto its other side. Attach the Left Upright, the other Base

 

 

 

Leg, the left Front Wheel, and the other Base Pads (not

 

 

 

 

shown) as described in steps 1 through 3. (Note: There is

 

 

 

 

not a wire harness in the Left Upright.)

Do not fully

 

 

 

tighten the bolts until step 6 is completed.

 

 

 

 

5. With the help of another person, carefully raise the

 

5

 

 

Uprights (35, 58) to the vertical position, with the wheels

 

 

 

 

 

and the walking platform on the floor as shown on page 5.

 

 

 

41

 

 

 

 

 

44

 

 

 

 

 

 

Have the other person hold a Handgrip Post (41) on the

 

 

125

 

Left Upright (35) as shown.

Hold a Post Spacer (43) in-

125

 

side of the Handgrip Post.

Insert a Post Bolt (44) with a

 

 

 

 

 

1/4” Washer (125) through the end hole in the Handgrip

 

 

 

 

Post and

through the Post Spacer

. Finger tighten

the

 

 

Post Bolt. Finger tighten another Post Bolt (44) with a 1/4”

43

 

 

Washer (125) into the other hole. If necessary, tap the

 

 

End

 

Handgrip Post with a rubber mallet to make sure that it is

 

 

 

 

 

Hole

 

fully seated.

Tighten the Post Bolt in the end hole

 

.

 

 

 

 

Then, tighten the other Post Bolt.

 

 

 

35

 

 

 

 

 

 

 

Attach the other Handgrip Post (41) to the right Upright

 

 

 

 

(not shown) as described above.

 

 

 

 

 

6. Have another person hold the Console Base (52) near

 

6

 

 

the Uprights (35, 58). Locate the wire harness extending

Wire Harness

 

 

 

from the Console Base. Connect the wire harness to the

 

 

 

 

Wire Harness (55) in the Right Upright.

If the connectors

 

 

 

do not fit together easily, rotate them and then con-

 

 

 

52

nect them.

Carefully feed the connectors and the excess

113

 

 

 

wire harness into the Right Upright. Carefully set the

 

 

 

 

 

 

 

Console Base on the posts on the Uprights.

 

 

55

 

 

 

 

 

 

 

Finger tighten four Console Bolts (42) with four Star

 

42

 

 

Washers (113) into the Uprights (35, 58) and the Console

 

 

 

 

 

Base (52). After all four Console Bolts have been started,

 

58

113

tighten them.

 

 

 

 

 

 

 

 

 

 

See step 1. Tighten the two Upright Bolts (66). Next,

 

 

 

42

tighten the four Base Leg Bolts (77). Make sure that

 

 

 

35

the Base Leg Nuts (70) are fully seated in the square

 

 

 

 

 

 

 

holes. Note: It may be helpful to tip the treadmill onto

 

 

 

 

its side while you do this.

 

 

 

 

 

 

 

 

 

7

 

 

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Mon.-Fri., 6 a.m.-6 p.m. MST QUESTIONS?Model No. RBTL69920 Serial No Customer HOT LineTable of Contents Treadmill is capable of high speeds Important PrecautionsUse the treadmill only as described Same circuit. Do not use an extension cordShown at 80% of actual size Never insert or drop any object into any openingRight Side Before YOU BeginFor your benefit, read this manual carefully before Left SideLeft AssemblyRubber mallet Wire cutters Phillips TightenDo not fully 55If. the connectors do not fit together easilyIts side while you do this 105 104 100 106 Insert two 1/2 Screws 51 into the two holesAttach the Left Foot Rail not shown in the same way 106Base Attach the Latch Assembly 37 and the Latch SpacerChest Pulse Sensor Troubleshooting HOW to USE the Chest Pulse SensorHOW to PUT on the Chest Pulse Sensor Chest Pulse Sensor Care and MaintenanceGrounded Outlet Box HOW to Plug in the Power CordPerformant Lube This product must be grounded.If it should malfuncFeatures of the Console Console DiagramTo reduce the possibility of electric shock HOW to USE the Manual Mode HOW to Turn on the PowerMeasure your heart rate, if desired See page 23 and turn off the demo modeTime/Incline/Segment Time display DisplayStart the program HOW to USE Personal Trainer ProgramsCompleted, all speed settings will move one col Press the Start button or the SpeedPercentages HOW to USE Heart Rate ProgramsFollow your progress with the displays Put on the chest pulse sensorDecrease Enter your ageHOW to Connect Your Portable Stereo HOW to Connect Your Portable CD PlayerVideocassettes HOW to Connect Your Computer HOW to Connect Your Home StereoAudio HOW to Connect Your VCRAudio Adapter Cable Insert the key into the consoleSpeed Next settings of the CD or video programWhen the CD or video program is completed, When you are finished using themHOW to USE Programs Directly from OUR WEB Site Speed Button so the display is blank Information MODE/DEMO ModeHOW to Fold the Treadmill for Storage Fat Calories/Heart Rate Display should be blankTripped Reset Position TroubleshootingHOW to Move the Treadmill HOW to Lower the Treadmill for USESolution Changing, remove the key Problem The chest pulse sensor does not function properlyBattery Belt has shifted to the leftExercise Frequency Conditioning GuidelinesExercise Intensity Workout GuidelinesPart No R0103A Ordering Replacement PartsLimited Warranty Icon Health & FITNESS, INC., 1500 S W., LOGAN, UTThick Base Pad Base Leg NutStar Washer Foot Rail WasherLift Frame Front Wheel Cover 108 Post Spacer On/Off SwitchPost Bolt IFit Wire Black Wire, 2F Key Qty DescriptionExploded R0103A
Top Page Image Contents