Reebok Fitness RBTL79607.1 manual Troubleshooting, Important The treadmill is not

Page 22

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, see the front cover of this manual.

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor

is plugged into a properly grounded outlet (see page 11). Use only a single-outlet surge suppres-

sor that meets all of the specifications described on page 11.

IMPORTANT: The treadmill is not

compatible with GFCI-equipped outlets.

 

 

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c. Check the reset/off circuit breaker located on the

c

 

treadmill frame near the power cord. If the switch pro-

 

trudes as shown, the circuit breaker has tripped. To

 

 

reset the circuit breaker, wait for five minutes and

Tripped

Reset

then press the switch to the reset position.

PROBLEM: The power turns off during use

 

 

SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait

for five minutes and then press the switch to the reset position.

 

b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five

minutes, and then plug it back in.

 

 

c. Remove the key from the console. Reinsert the key into the console.

 

d. If the treadmill still will not run, see the front cover of this manual.

 

PROBLEM: The displays of the console do not function properly

 

 

SOLUTION: a. Remove the key from the console and UNPLUG THE

a

 

POWER CORD. Next, carefully lower the Uprights

 

(111, 113). Remove the two indicated #8 x 1/4" Tek

 

 

Screws (71). Note: A Phillips screwdriver with a shaft

 

 

at least 8 in. (20 cm) long is needed.

 

 

 

111

71

 

 

Raise the Uprights (111, 113) to the vertical position. Remove the three #8 x 3/4" Screw (6) from the Motor Hood (33), and carefully pivot the Motor Hood off.

111

6

113

33

 

 

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT QUESTIONS?Model No. RBTL79607.1 Serial No On the WEBTable of Contents Important Precautions Pulse sensor is not a medical devicePage Before YOU Begin Assembly Make sure that the power cord is unpluggedPage Before tightening either of them Wire Harnesses 73, 119 are not pinched Pull on the sleeve to make sure that it is locked into place HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleHOW to USE the Manual Mode HOW to Turn on the PowerInsert the key into the console Time/Pace Measure your heart rate if desired Select a classic workout HOW to USE a Classic WorkoutFollow your progress with the matrix and the displays Enter your weight HOW to USE a Weight Loss WorkoutSelect a weight loss workout HOW to Create a Custom Workout Select one of the custom workoutsHOW to USE a Custom Workout HOW to USE the Sound System Information ModeMake sure that the audio wire is fully plugged HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USEImportant The treadmill is not TroubleshootingProblem The power turns off during use Compatible with GFCI-equipped outletsProblem The walking belt slows when walked on TopProblem Solution Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencyPart LIST-Model No. RBTL79607.1 Qty DescriptionQty Exploded Drawing A-Model No. RBTL79607.1 R0709A Exploded Drawing B-Model No. RBTL79607.1 R0709A Exploded Drawing C-Model No. RBTL79607.1 R0709A Exploded Drawing D-Model No. RBTL79607.1 R0709A Limited Warranty Ordering Replacement PartsIcon Health & Fitness, Inc., 1500 S W., Logan, UT
Top Page Image Contents