Woodstock manual Model M1001 Shop FOX Vertical Mill 6 X

Page 5

M1001 6" x 26" Vertical Mill

MODEL M1001

SHOP FOX® VERTICAL MILL 6" X 26"

Motors
Main
Type	TEFC Capacitor Start Induction
Horsepower	1-1/2 HP
Voltage	110V/220V
Prewired	110V
Phase	Single-Phase
Amps	16A at 110V, 8A at 220V
Speed	1725 RPM
Cycle	60 Hz
Number of Speeds	1
Power Transfer	V-Belt Drive
Bearings	Shielded, Permanently Lubricated
Main Specifications
Operation Info
Spindle Travel	3 in.
Swing	11 in.
Longitudinal Table Travel	14-1/4 in.
Cross Table Travel	6 in.
Vertical Table Travel	14 in.
Knee Travel	11-3/4 in
Ram Travel	12 in.
Head Travel	2-1/2 in.
Head Swivel (Left-to-Right)	90 deg.
Head Swivel (Front-to-Back)	45 deg.
Turret or Column Swivel (Left and Right)	360 deg.
Maximum Distance Spindle to Column	5-1/2 in.
Maximum Distance Spindle to Table	11-7/8 in.
Drilling Capacity for Cast Iron	1 in.
Drilling Capacity for Steel	3/4 in.
Number of Vertical Spindle Speeds	9
Range of Vertical Spindle Speeds	240, 360, 520, 730, 1280, 1320, 1600, 2220, 2760 RPM
Number of Longitudinal Feeds	Variable
Feed Rate	0 — 140 FPM
Quill Diameter	2.950 in.

INTRODUCTION

-3-

Image 5

Contents 26 Vertical Mill Page Table of Contents About Your New 6 x 26 Vertical Mill IntroductionWoodstock Technical Support Model M1001 Shop FOX Vertical Mill 6 X Lead Screw Info Electrical Controls and Features Standard Machinery Safety Instructions SafetySafety Additional Safety Instructions for Vertical Mills Availability ElectricalFull-Load Current Rating Full-Load Current Rating atNominal Voltage 220V/240V Cycle 60 Hz Phase Nominal Voltage 110V/120V Cycle 60 Hz PhaseCircuit Information Circuit Requirements forVoltage Conversion Grounding & Plug RequirementsExtension Cords Inventory SET UPUnpacking M1001 minimum working clearances Machine Placement Cleaning MachineBolting to Concrete Floors Using Machine MountsMounting Mill on Shop Floor Headstock Adjustment AssemblyHandle Installation DrawbarTest Run To begin the test run procedure, do these stepsSpindle Controls Positioning Spindle Head OperationsGeneral Longitudinal Feed Control Table TravelCross Feed Knee FeedExample Power Feed ControlsGraduated Dials Quill Travel Micro-feed Depth AdjustmentQuill Feed Control To use the quill feed handle, do these stepsCutting Speeds for High Speed Steel HSS Cutting Tools Determining Needed RPMUnplug the Mill Setting RPMSpindle Break-in Procedure Removing Cutting Tools Installing ToolsTo load a tool in the spindle, do these steps To remove cutting tools, do these stepsTable and Base MaintenanceCleaning Lubrication Power FeedSingle Shot Lubrication System Knee Elevating ScrewMaintenance Notes Maintenance ScheduleGibs ServiceLongitudinal Feed Adjustment Adjusting BacklashCrossfeed Adjustment To adjust the backlash, do these stepsWiring Diagram Color KEY Electrical Safety InstructionsStop Electrical Parts IdentificationVAC 150F Capacitor Wiring DiagramSymptom Possible Cause TroubleshootingHeadstock Assembly Base Assembly Description Machine Parts ListsCross Lead Screw Description Machine LabelsWarranty Comments Warranty RegistrationWoodstock international inc. p.o. box Bellingham, wa