Woodstock M1001 manual Set Up, Unpacking, Inventory

Page 15

M1001 6" x 26" Vertical Mill

SET UP

Unpacking

The SHOP FOX® Model M1001 has been carefully pack- aged for safe transporting. If you notice the machine has been damaged, please contact your authorized SHOP FOX® dealer immediately.

Inventory

The following is a description of the main components shipped with the SHOP FOX® Model M1001. Lay the components out to inventory them.

Wooden Box Contents (Figures 3 & 4)		Qty
A.	Milling Machine	1
B.	Toolbox	1
Toolbox Contents (Figure 4)		Qty
C. 3" Shell Mill with Arbor		1
D.	Handwheels	2
E.	Handwheel Handles	4

Figure 3. Model M1001.

B

SET UP

F.	Drawbar with Locking Nut	1
G.	Spare V-Belts	2
H.	220V ON/OFF Switch	1
I.	Open End Wrenches 17/19mm & 12/14mm	2
J.	T-Slot Bolts M12-1.75 x 40	2
K.	Screwdriver	1
L.	Phillips Head Screwdriver	1
M.	Hex Wrenches 3, 4, 5, & 6mm	4

K

L

C

M

H

J

G

I

E

Inventory parts not shown:
• Power Feed Instruction Manual	..........................1

If any parts are missing, find the part number in the back of this manual and contact Woodstock International, Inc. at (360) 734-3482 or at tech-support@shopfox.biz

SUFFOCATION HAZARD!

Immediately discard all plastic bags and packing materials to eliminate choking/suffocation hazards for chil- dren and animals.

F

D

Figure 4. Toolbox contents.

NOTICE

When ordering replacement parts, refer to the parts list and diagram in the back of the manual.

-13-

Image 15

Contents 26 Vertical Mill Page Table of Contents Introduction Woodstock Technical SupportAbout Your New 6 x 26 Vertical Mill Model M1001 Shop FOX Vertical Mill 6 X Lead Screw Info Electrical Controls and Features Standard Machinery Safety Instructions SafetySafety Additional Safety Instructions for Vertical Mills Full-Load Current Rating at ElectricalAvailability Full-Load Current RatingCircuit Requirements for Nominal Voltage 110V/120V Cycle 60 Hz PhaseNominal Voltage 220V/240V Cycle 60 Hz Phase Circuit InformationGrounding & Plug Requirements Extension CordsVoltage Conversion SET UP UnpackingInventory M1001 minimum working clearances Machine Placement Cleaning MachineUsing Machine Mounts Mounting Mill on Shop FloorBolting to Concrete Floors Drawbar AssemblyHeadstock Adjustment Handle InstallationTo begin the test run procedure, do these steps Spindle ControlsTest Run Operations GeneralPositioning Spindle Head Knee Feed Table TravelLongitudinal Feed Control Cross FeedPower Feed Controls Graduated DialsExample To use the quill feed handle, do these steps Micro-feed Depth AdjustmentQuill Travel Quill Feed ControlCutting Speeds for High Speed Steel HSS Cutting Tools Determining Needed RPMUnplug the Mill Setting RPMSpindle Break-in Procedure To remove cutting tools, do these steps Installing ToolsRemoving Cutting Tools To load a tool in the spindle, do these stepsMaintenance CleaningTable and Base Knee Elevating Screw Power FeedLubrication Single Shot Lubrication SystemMaintenance Notes Maintenance ScheduleGibs ServiceTo adjust the backlash, do these steps Adjusting BacklashLongitudinal Feed Adjustment Crossfeed AdjustmentWiring Diagram Color KEY Electrical Safety InstructionsStop Electrical Parts IdentificationVAC 150F Capacitor Wiring DiagramSymptom Possible Cause TroubleshootingHeadstock Assembly Base Assembly Description Machine Parts ListsCross Lead Screw Description Machine LabelsWarranty Comments Warranty RegistrationWoodstock international inc. p.o. box Bellingham, wa