Epic Fitness EPTL09605.0 manual Troubleshooting, Problem The power turns off during use

Page 22

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please see the front cover of this manual.

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 9). Use only a single-outlet surge suppressor that meets all of the specifications described on page 9. Important: The treadmill is not compatible with GFCI-equipped outlets.

b. Make sure that the key is inserted into the console.

c.Check the reset/off circuit breaker located on the frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

PROBLEM: The power turns off during use

c

Off Reset

SOLUTION: a. Check the reset/off circuit breaker (see 1. c. above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c. Remove the key from the console and then reinsert it.

PROBLEM: The displays of the console do not function properly

SOLUTION: a. Remove the key from the console and UNPLUG THE

a

 

POWER CORD. Next, remove the screws from the hood

 

 

 

and carefully remove the hood. Locate the Reed Switch

1/8”

 

(42) and the Magnet (24) on the left side of the Pulley (23).

 

23

Turn the Pulley until the Magnet is aligned with the Reed

42

24

Switch. Make sure that the gap between the Magnet

 

and the Reed Switch is about 1/8”. If necessary, use a

Top

 

slotted screwdriver to move the Reed Switch slightly.

 

View

 

Reattach the Hood, making sure that the Screws are in-

 

 

 

serted into the same holes from which they were removed.

 

 

Run the treadmill for a few minutes to check for a correct

 

 

speed reading.

 

 

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents
Call TOLL-FREE QUESTIONS?Model No. EPTL09605.0 Serial No Mon.-Fri., 6 a.m.-6 p.m. MSTTable of Contents Important Precautions Treadmill OperationPage Back Before YOU BeginRight Side Assembly Not overtighten the Nut the Wheel should turn freely Tape Treadmill Operation HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Features of the Console HOW to Turn on the PowerStart the walking belt HOW to USE the Manual ModeInsert the key into the console Change the incline of the treadmill as desiredDemo mode When you are finished exercising, removeAdjust the incline of the treadmill to the lowest When you are finished using the treadmillHOW to USE a Preset Program Select a preset programFollow your progress with the displays HOW to Create a Custom Program Select a custom programHOW to USE a Custom Program HOW to USE a Heart Rate Program Select a heart rate programIf heart rate program Information MODE/DEMO Mode Optional Chest Pulse SensorHOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USE Switch. Make sure that the gap between the Magnet TroubleshootingProblem The power turns off during use Reed Switch is about 1/8. If necessary, use a TopProblem The walking belt slows when walked on Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencySuggested Stretches Page R1105A Key No. Qty. DescriptionExploded DRAWING-Model No. EPTL09605.0 108 100 101 104 103 102 Limited Warranty HOW to Order Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT