Epic Fitness eptl20912.0 manual Operation and Adjustment, HOW to Connect the Power Cord

Page 12

OPERATION AND ADJUSTMENT

HOW TO CONNECT THE POWER CORD

Use a Surge Suppressor

Your treadmill, like other electronic equipment, can be damaged by sudden voltage changes in your home’s power. Voltage surges, spikes, and noise interfer- ence can result from weather conditions or from other appliances being turned on or off. To decrease the risk of damaging the treadmill, always use a surge suppressor with the treadmill. To purchase a surge suppressor, see precaution 13 on page 3.

Use only a surge suppressor that is UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a UL suppressed voltage rating of 400 volts or less and a minimum surge dissipation of 450 joules. The surge suppressor must also be electri- cally rated for 120 volts AC and 15 amps. There must be a monitoring light on the surge suppressor to indi- cate whether it is functioning properly. Failure to use a properly functioning surge suppressor could result in damage to the control system of the treadmill and serious injury to users.

Plug in the Power Cord

nominal 120-volt circuit capable of carrying 15 or more amps. To avoid overloading the circuit, do not plug other electrical devices, except for low- power devices such as cell phone chargers, into the surge suppressor or into an outlet on the same circuit. IMPORTANT: The treadmill is not compat- ible with GFCI-equipped outlets and may not be compatible with AFCI-equipped outlets.

1

Grounded Outlet

Grounding Pin

Grounding Pin

Surge

Suppressor

The treadmill must be grounded. If it should malfunc- tion or break down, grounding provides a path of least resistance for electric current to reduce the risk of elec- tric shock. The treadmill power cord has a plug with a grounding pin (see drawing 1 on this page).

DANGER: Improper connection of the power cord increases the risk of elec- tric shock. Do not modify the plug—if it will not fit an outlet, have a proper outlet installed by a qualified electrician. If you are unsure

Atemporary adapter may be used to connect the surge sup- pressor to a 2-pole receptacle if a properly grounded outlet is not available.

2

2-pole Receptacle

Adapter

Lug

Metal

Screw

whether the treadmill is properly grounded, contact a qualified electrician.

Plug the power cord into a surge suppressor, and plug the surge suppressor into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. The outlet must be on a

The lug or wire extending from the adapter must be connected with a metal screw to a permanent ground such as a properly grounded outlet box cover.

Some 2-pole receptacle outlet box covers are not grounded. Before using an adapter, contact a quali- fied electrician to determine whether the outlet box cover is grounded. The temporary adapter should be used only until a properly grounded outlet can be installed by a qualified electrician.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents QUESTIONS? Model No. EPTL20912.0 Serial NoVisit OUR Website CallTable of Contents Important Precautions Page Before YOU Begin Part Identification Chart Assembly Power cordDecal is on the side of the Cover as shown See the inset drawing. Press the left handrailBe careful not to pinch the Upright Connect the pulse wires on the right side not Shown also Again. if YOU do not Connect the CONSide is shown. Start all four Screws and then Tighten them Page HOW to PUT on the Heart Rate Monitor Care and MaintenanceTroubleshooting Chest Heart Rate MonitorOperation and Adjustment HOW to Connect the Power CordUse a Surge Suppressor Diagram Features of the ConsoleConsole HOW to Turn on the Power HOW to USE the Touch ScreenHOW to SET UP the Console HOW to USE the Manual Mode When you are finished exercising, remove Power cord. Important If you do not doKey from the console This, the treadmill’s electrical components mayHOW to USE AN Onboard Workout Select an onboard workoutStart the workout HOW to USE a SET-A-GOAL Workout Select the main menu. See on Select a set-a-goal workoutHOW to Create a USER-DEFINED Workout Select a user-defined workoutHOW to USE a USER-DEFINED Workout Change the workout if desiredHOW to USE AN Ifit Workout Start the workout. See onHOW to USE the Equipment Settings Mode HOW to USE the Maintenance Mode HOW to USE the Wireless Network Mode Enable Wi-FiSet up and manage a wireless network connection Exit the wireless network modeHOW to USE the Stereo Sound System Make sure that your audio wire is fully pluggedHOW to USE the Internet Browser HOW to Fold and Move the Treadmill HOW to Fold the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USETroubleshooting Symptom The power turns off during useSymptom The iFit mode does not function correctly Symptom The walking belt slows when walked on Maintenance CleaningStorage Exercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencySuggested Stretches Part List Qty DescriptionDescription Qty Exploded Drawing a Exploded Drawing B Exploded Drawing C Exploded Drawing D Exploded Drawing E Ordering Replacement Parts Limited WarrantyIcon Health & Fitness, Inc., 1500 S W., Logan, UT
Top Page Image Contents