Gold's Gym GGTL30611.0 manual Troubleshooting, Compatible with GFCI-equipped outlets

Page 20

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, see the front cover of this manual.

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor

is plugged into a properly grounded outlet (see page 13). Use only a single-outlet surge suppres-

sor that meets all of the specifications described on page 13. IMPORTANT: The treadmill is not

compatible with GFCI-equipped outlets.

 

 

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c. Check the power switch located on the treadmill

c

 

frame near the power cord. If the switch protrudes

 

as shown, the switch has tripped. To reset the

 

 

switch, wait for five minutes and then press the

Tripped

Reset

switch back in.

PROBLEM: The power turns off during use

 

 

SOLUTION: a. Check the power switch (see the drawing above). If the switch has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in.

c.Remove the key from the console. Reinsert the key into the console.

d.If the treadmill still will not run, please see the front cover of this manual.

PROBLEM: The displays of the console do not function properly

SOLUTION: a. Remove the key from the console and UNPLUG THE

a

 

20

POWER CORD. Remove the three indicated M4.2 x

65

19mm Hood Screws (20) and two M5.5 x 25mm

 

 

Screws (25). Then, carefully remove the Motor Hood

 

 

 

(65).

 

25

 

 

 

 

Locate the Reed Switch (89) and the Magnet (62) on the left side of the Pulley (71). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8 in. (3 mm). If necessary, loosen the M4.2 x 13mm Tek Screw (3), move the Reed Switch slightly, and then retighten the Screw. Reattach the Motor Hood (not shown), and run the treadmill for a few minutes to check for a correct speed reading.

1/8 in.

 

71

89

62

Top View

 

 

20

Image 20
Contents QUESTIONS? Model No. GGTL30611.0 Serial NoTable of Contents Important Precautions Page Before YOU Begin Assembly Make sure that the power cord is unplugged Overtighten the Nuts the Wheels should turn FreelyHold the Left Upright 53 so that the small Holes are positioned as shown. Attach the LeftBolt yet Top ViewConsole Tie Wire Bracket Large Hole Small Wire Tie 103 Console Console Wire Tie Into the Uprights. Then, firmly tighten all four Bolts Knob Spring Collar Large Hole Pin PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeInsert the key into the console Start the walking beltMeasure your heart rate if desired. Before using Follow your progress with the displays. The lower leftHOW to USE a Preset Workout Start the workoutInformation Mode HOW to Fold and Move the Treadmill HOW to Fold the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USECompatible with GFCI-equipped outlets TroubleshootingProblem The power turns off during use Problem The walking belt slows when walked on Walking belt. If the walking belt has shifted toExercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencyPart List Qty DescriptionExploded Drawing a Exploded Drawing B Exploded Drawing C Exploded Drawing D Icon Health & Fitness, Inc., 1500 S W., Logan, UT Ordering Replacement PartsLimited Warranty