PART LIST
Model No. GGTL30611.0 R0911A
Key No. | Qty. | Description | Key No. | Qty. | Description |
1 | 2 | M10 x 60mm Patch Bolt | 53 | 1 | Left Upright |
2 | 6 | M10 x 58mm Bolt | 54 | 1 | Right Upright |
3 | 2 | M4.2 x 13mm Tek Screw | 55 | 1 | Idler Roller |
4 | 6 | M4.2 x 16mm Screw | 56 | 1 | Drive Motor Belt |
5 | 4 | M8 Star Washer | 57 | 1 | Electronics Bracket |
6 | 1 | Latch Warning Decal | 58 | 1 | 3/8" x 1 3/4" Bolt |
7 | 2 | M5 Star Washer | 59 | 1 | Motor Bracket |
8 | 4 | M8 x 15mm Bolt | 60 | 1 | Left Idler Roller Bracket |
9 | 6 | M10 Star Washer | 61 | 1 | Right Idler Roller Bracket |
10 | 12 | M4.2 x 19mm Screw | 62 | 1 | Magnet |
11 | 4 | Frame Spacer | 63 | 4 | Base Foot |
12 | 1 | Console Back | 64 | 1 | Latch Plate |
13 | 2 | #10 x 1" Tek Screw | 65 | 1 | Motor Hood |
14 | 2 | M10 Flat Washer | 66 | 1 | Belly Pan |
15 | 1 | Key/Clip | 67 | 1 | Left Foot Rail |
16 | 4 | M10 Nut | 68 | 1 | Right Foot Rail |
17 | 1 | 6 mm Hex Key | 69 | 4 | Wheel Spacer |
18 | 1 | 4 mm Hex Key | 70 | 2 | Wheel |
19 | 4 | M8 x 30mm Screw | 71 | 1 | Drive Roller/Pulley |
20 | 3 | M4.2 x 19mm Hood Screw | 72 | 1 | 3/8" x 1 1/4" Bolt |
21 | 6 | M4.2 x 13mm Screw | 73 | 2 | Caution Decal |
22 | 1 | Left Handrail | 74 | 1 | Rear Foot, Left |
23 | 1 | Lift Frame | 75 | 4 | M5.5 x 30mm Screw |
24 | 1 | Latch Pin Assembly | 76 | 1 | Walking Belt |
25 | 6 | M5.5 x 25mm Screw | 77 | 4 | Handrail Cap |
26 | 4 | M4.2 x 19mm Tek Screw | 78 | 2 | Platform Cushion |
27 | 2 | M8 x 35mm Screw | 79 | 1 | Drive Motor |
28 | 4 | M4.2 x 13mm Belt Guide Screw | 80 | 2 | Wire Tie |
29 | 2 | Idler Roller Adjustment Bolt | 81 | 12 | 8" Tie |
30 | 2 | 1/4" Motor Bolt | 82 | 1 | 3/8" Locknut |
31 | 1 | M8 x 102mm Bolt | 83 | 1 | Reed Switch Clamp |
32 | 2 | M4 x 10mm Controller Screw | 84 | 2 | M4 x 10mm Ground Screw |
33 | 1 | Right Handrail | 85 | 2 | M5 x 16mm Screw |
34 | 2 | M8 x 20mm Bolt | 86 | 1 | Walking Platform |
35 | 2 | M10 x 60mm Bolt | 87 | 1 | Controller |
36 | 2 | M6 Star Washer | 88 | 1 | Console Crossbar |
37 | 1 | Power Switch | 89 | 1 | Reed Switch |
38 | 2 | M8.4 Star Washer | 90 | 1 | Power Cord |
39 | 1 | Wire Harness | 91 | 1 | Console Assembly |
40 | 1 | Incline Motor | 92 | 1 | 3/8" Jam Nut |
41 | 4 | M4.2 x 13mm Belly Pan Screw | 93 | 2 | Belt Guide |
42 | 4 | M4.2 Star Washer | 94 | 1 | 5mm Hex Key |
43 | 1 | Hex Key | 95 | 2 | Frame Cap |
44 | 6 | M8 Flange Nut | 96 | 1 | Releasable Tie |
45 | 2 | Isolator | 97 | 1 | Rear Foot, Right |
46 | 1 | M8 Jam Nut | 98 | 2 | Base Cap |
47 | 3 | Hood Clip | 99 | 1 | Power Cord Grommet |
48 | 1 | Latch Housing | 100 | 1 | Incline Motor Wire |
49 | 2 | Grommet | 101 | 2 | Front Roller Washer |
50 | 4 | Cushion Fastener | 102 | 3 | M4.2 x 18mm Screw |
51 | 1 | Frame | 103 | 4 | Cage Nut |
52 | 1 | Base | * | – | Userʼs Manual |
Note: Specifications are subject to change without notice. For information about ordering replacement parts, see the back cover of this manual. *These parts are not illustrated.
23