Gold's Gym GGTL30611.0 manual Problem The walking belt slows when walked on

Page 21

PROBLEM: The walking belt slows when walked on

SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 13.

b. If the walking belt is overtightened, treadmill perfor-

b

2–3 in.

mance may decrease and the walking belt may be-

come damaged. Remove the key and UNPLUG THE

 

 

POWER CORD. Using the hex key, turn both idler

 

 

roller bolts counterclockwise, 1/4 of a turn. When the

 

 

walking belt is properly tightened, you should be able

 

 

to lift each edge of the walking belt 2 to 3 in. (5 to 7

 

 

cm) off the walking platform. Be careful to keep the

 

Idler Roller

walking belt centered. Then, plug in the power cord,

 

insert the key, and run the treadmill for a few minutes.

 

Bolts

Repeat until the walking belt is properly tightened.

 

 

c.If the walking belt still slows when walked on, please see the front cover of this manual.

PROBLEM: The walking belt is off-center or slips when walked on

SOLUTION: a. If the walking belt has shifted to the left, first re-

 

 

 

 

 

 

 

 

 

a

 

 

move the key and UNPLUG THE POWER CORD.

 

 

 

Using the hex key, turn the left idler roller bolt clock-

 

 

 

 

wise 1/2 of a turn. Be careful not to overtighten the

 

 

 

 

walking belt. If the walking belt has shifted to the

 

 

 

 

right, turn the left idler roller bolt counterclockwise 1/2

 

 

 

 

of a turn. Then, plug in the power cord, insert the key,

 

 

 

 

and run the treadmill for a few minutes. Repeat until

 

 

 

 

the walking belt is centered.

 

 

 

 

 

 

 

 

b. If the walking belt slips when walked on, first re-

b

move the key and UNPLUG THE POWER CORD.

Using the hex key, turn both idler roller bolts clock-

 

wise, 1/4 of a turn. When the walking belt is correctly

 

tightened, you should be able to lift each edge of the

 

walking belt 2 to 3 in. (5 to 7 cm) off the walking plat-

 

form. Be careful to keep the walking belt centered.

 

Then, plug in the power cord, insert the key, and care-

 

fully walk on the treadmill for a few minutes. Repeat

 

until the walking belt is properly tightened.

 

PROBLEM: The incline of the treadmill does not change correctly

 

SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re-

move the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the

maximum incline level and then return to the minimum level. This will recalibrate the incline system.

PROBLEM: The console displays remain lit when you remove the key from the console

SOLUTION: a. The console features a display demo mode, designed to be used if the treadmill is displayed in a

store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off

the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE

INFORMATION MODE on page 18 to turn off the demo mode.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Model No. GGTL30611.0 Serial No QUESTIONS?Table of Contents Important Precautions Page Before YOU Begin Assembly Overtighten the Nuts the Wheels should turn Freely Make sure that the power cord is unpluggedHold the Left Upright 53 so that the small Holes are positioned as shown. Attach the LeftTop View Bolt yetConsole Tie Wire Bracket Large Hole Small Wire Tie 103 Console Console Wire Tie Into the Uprights. Then, firmly tighten all four Bolts Knob Spring Collar Large Hole Pin Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerInsert the key into the console Start the walking beltFollow your progress with the displays. The lower left Measure your heart rate if desired. Before usingStart the workout HOW to USE a Preset Workout Information Mode HOW to Fold the Treadmill HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USETroubleshooting Problem The power turns off during useCompatible with GFCI-equipped outlets Walking belt. If the walking belt has shifted to Problem The walking belt slows when walked onExercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencyQty Description Part ListExploded Drawing a Exploded Drawing B Exploded Drawing C Exploded Drawing D Ordering Replacement Parts Limited WarrantyIcon Health & Fitness, Inc., 1500 S W., Logan, UT
Top Page Image Contents