Gold's Gym GGTL07819.0 manual Not Connected PROPERLY, the CON Sole MAY be Damaged When

Page 10

9. Set the console assembly face down on a soft

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

9

 

 

 

 

 

 

surface to avoid scratching the console assem-

 

 

 

 

 

 

 

bly. Remove the two #8 x 3/4" Screws (1). Lift

 

 

 

 

 

 

 

 

off the Pulse Bar (90). Save the Pulse Bar and

 

 

 

1

 

 

90

 

the two Screws for assembly steps 10 and

 

 

 

 

 

 

 

12.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Console

 

 

 

 

 

Assembly

 

10. Set the Pulse Bar (90) on the Left and Right

10

4

 

 

 

Uprights (77, 92). Attach the Pulse Bar with four

 

 

 

#10 x 3/4" Screws (4) and four #10 Star

 

12

 

 

 

Washers (12). Start all four Screws before

 

 

 

 

firmly tightening any of them. Be careful not

 

5

90

 

 

to pinch the Wire Harness (91).

 

4

 

Firmly tighten the four 5/16" x 1 3/4" Bolts

 

 

 

12

(5).

 

 

 

 

 

 

77

 

5

91

 

 

 

 

 

 

 

 

92

 

11. While a second person holds the console as-

11

 

Console

Console

 

sembly near the Pulse Bar (90), connect the

 

 

Console Ground Wire (89) on the Pulse Bar to

 

 

Assembly

Wire

 

the ground wire from the console assembly.

 

 

 

 

 

Connect the console wire to the Wire Harness

 

 

 

(91). See the inset drawing. The connectors

Ground

 

 

should slide together easily and snap into

 

91

place. If they do not, turn one connector and

Wire

 

then try again. IF THE CONNECTORS ARE

 

 

 

NOT CONNECTED PROPERLY, THE CON-

 

 

 

SOLE MAY BE DAMAGED WHEN THE

 

89

 

POWER IS TURNED ON. Lay the wires inside

 

Console Wire

the bottom of the Pulse Bar (90).

90

 

 

 

91

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT QUESTIONS?Model No. GGTL07819.0 Serial No On the WEBTable of Contents Important Precautions Pulse sensor is not a medical devicePage Before YOU Begin Assembly Do not fully fold the Frame yet Make sure that the power cord is unpluggedTighten the Nut the Wheel must turn freely Tighten the Bolts yet Careful not to pinch the Wire HarnessWith a second Bolt Spacer 95, 3/8 x 4 Bolt 3/8 Star Washer Not fully fold the Frame yetBolts yet Not Connected PROPERLY, the CON Sole MAY be Damaged When Screws before firmly tightening any of them Overtighten the Screws. Then, raiseRaise the Frame 48 to the position shown HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleSelect the manual mode HOW to Turn on the PowerHOW to USE the Manual Mode Insert the key into the consoleDisplays Matrix Measure your heart rate if desired. Before usingFollow your progress with the matrix Turn on the fan if desiredStart the program HOW to USE a Personal Trainer Quick ProgramSelect one of the personal trainer quick programs Follow your progress with the matrix and the displaysHOW to Create Your OWN Quick Program Select a custom quick programHOW to USE Your OWN Quick Program Select a custom quick programsInformation Mode HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USEProblem The power turns off during use TroubleshootingCompatible with GFCI-equipped outlets Problem The walking belt slows when walked on TopProblem Solution Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencyPart LIST-Model No. GGTL07819.0 Key No. Qty DescriptionBlue Wire, M/F Userʼs Manual Exploded Drawing A-Model No. GGTL07819.0 R0809A Exploded Drawing B-Model No. GGTL07819.0 R0809A Exploded Drawing C-Model No. GGTL07819.0 R0809A Exploded Drawing D-Model No. GGTL07819.0 R0809A Limited Warranty Ordering Replacement PartsIcon Health & Fitness, Inc., 1500 S W., Logan, UT
Top Page Image Contents