Gold's Gym GGTL07819.0 manual Make sure that the power cord is unplugged

Page 7

1. Make sure that the power cord is unplugged.

1

 

 

 

Hole

 

With the help of a second person, carefully tip

 

 

91

 

97

 

the treadmill onto its left side. Partially fold the

 

 

 

 

Frame (48) so that the treadmill is more stable;

 

 

 

 

 

 

6

do not fully fold the Frame yet.

 

 

 

 

96

 

Cut the shipping tie securing the Wire Harness

 

 

 

 

 

 

(91) to the Base (96). Locate a plastic tie in the

 

 

 

 

 

 

 

indicated hole in the Base, and use the tie to pull

 

 

 

 

 

 

 

the Wire Harness out of the hole.

48

98 97 6

 

 

 

 

Attach two Base Feet (97) to the Base (96) in the

 

 

 

 

locations shown with two #8 x 1" Tek Screws (6)

 

 

 

 

 

 

 

and two Base Foot Spacers (98).

 

 

 

 

 

97

Then, attach the other two Base Feet (97) with

 

 

 

 

 

 

 

 

 

 

 

6

two #8 x 1" Tek Screws (6).

 

 

 

 

 

 

 

 

98

97

 

 

 

 

 

 

 

 

 

 

 

2. See the inset drawing. Cut the plastic tie near

2

Plastic Tie

 

 

 

 

the Wire Harness (91).

 

 

 

 

Attach a Wheel (99) with a 3/8" x 2" Bolt (9) and

 

 

 

 

 

 

 

a 3/8" Nut (10) to the Base (96). Do not over-

 

 

 

 

 

 

 

tighten the Nut; the Wheel must turn freely.

9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1099

96

 

Cut

 

 

 

 

 

 

91

 

 

3. Identify the Right Upright (92) and the Right

3

 

 

 

 

 

 

Upright Spacer (100), which are marked with

 

 

 

 

 

 

“Right” stickers. Insert the Wire Harness (91)

 

 

 

 

92

 

 

through the Right Upright Spacer as shown. Set

 

 

 

 

 

 

the Right Upright Spacer on the Base (96).

91

 

 

 

 

 

 

With the help of a second person, hold the Right

 

 

 

 

91

Wire Tie

 

 

 

Upright (92) near the Base (96). See the inset

 

100

 

drawing. Tie the wire tie in the Right Upright se-

 

 

 

 

 

 

curely around the end of the Wire Harness (91).

 

 

 

 

 

 

96

Then, pull the other end of the wire tie until the

 

 

 

 

 

 

Wire Harness is routed completely through the

 

 

 

 

 

 

 

Right Upright.

 

92

 

 

 

 

 

 

 

 

 

 

 

 

 

91

Wire

 

 

 

 

 

 

Tie

 

 

 

 

 

 

7

 

 

 

 

 

 

Image 7
Contents On the WEB QUESTIONS?Model No. GGTL07819.0 Serial No Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MTTable of Contents Pulse sensor is not a medical device Important PrecautionsPage Before YOU Begin Assembly Do not fully fold the Frame yet Make sure that the power cord is unpluggedTighten the Nut the Wheel must turn freely Not fully fold the Frame yet Careful not to pinch the Wire HarnessWith a second Bolt Spacer 95, 3/8 x 4 Bolt 3/8 Star Washer Tighten the Bolts yetBolts yet Not Connected PROPERLY, the CON Sole MAY be Damaged When Overtighten the Screws. Then, raise Screws before firmly tightening any of themRaise the Frame 48 to the position shown HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Features of the Console Console DiagramInsert the key into the console HOW to Turn on the PowerHOW to USE the Manual Mode Select the manual modeTurn on the fan if desired Measure your heart rate if desired. Before usingFollow your progress with the matrix Displays MatrixFollow your progress with the matrix and the displays HOW to USE a Personal Trainer Quick ProgramSelect one of the personal trainer quick programs Start the programSelect a custom quick program HOW to Create Your OWN Quick ProgramSelect a custom quick programs HOW to USE Your OWN Quick ProgramInformation Mode HOW to Lower the Treadmill for USE HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Move the TreadmillProblem The power turns off during use TroubleshootingCompatible with GFCI-equipped outlets Top Problem The walking belt slows when walked onProblem Solution Exercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesKey No. Qty Description Part LIST-Model No. GGTL07819.0Blue Wire, M/F Userʼs Manual Exploded Drawing A-Model No. GGTL07819.0 R0809A Exploded Drawing B-Model No. GGTL07819.0 R0809A Exploded Drawing C-Model No. GGTL07819.0 R0809A Exploded Drawing D-Model No. GGTL07819.0 R0809A Limited Warranty Ordering Replacement PartsIcon Health & Fitness, Inc., 1500 S W., Logan, UT