Gold's Gym GGTL03607.4 manual Top, Problem The walking belt slows when walked on

Page 19

Remove the three M4.2 x 19mm Washer Head

 

 

13

Screws (13) and carefully pivot the Hood (53) off.

 

53

 

 

 

Locate the Reed Switch (54) and the Magnet (42)

 

 

 

on the left side of the Pulley (44). Turn the Pulley

 

 

 

until the Magnet is aligned with the Reed Switch.

 

1/8 in.

 

Make sure that the gap between the Magnet and

 

42

the Reed Switch is about 1/8 in. (3 mm). If neces-

 

54

sary, loosen the M4.2 x 19mm Screw (1), move the

 

44

Reed Switch slightly, and then retighten the Screw.

 

Top

Reattach the Hood (not shown), and run the tread-

 

 

mill for a few minutes to check for a correct speed

 

View

 

reading.

 

 

 

PROBLEM: The incline of the treadmill does not change correctly

 

 

 

SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re-

move the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the

maximum incline level and then return to the minimum level. This will recalibrate the incline system.

PROBLEM: The walking belt slows when walked on

 

 

 

SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 11.

b. If the walking belt is overtightened, treadmill perfor-

b

 

 

mance may decrease and the walking belt may be-

2–3 in.

 

come damaged. Remove the key and UNPLUG THE

 

 

POWER CORD. Using the hex key, turn both rear

 

 

 

roller bolts counterclockwise,1/4 of a turn. When the

 

 

 

walking belt is properly tightened, you should be able

 

 

 

to lift each edge of the walking belt 2 to 3 in. (5 to 7

 

 

 

cm) off the walking platform. Be careful to keep the

 

 

 

walking belt centered. Then, plug in the power cord,

 

 

 

insert the key, and run the treadmill for a few min-

Rear Roller Bolts

 

utes. Repeat until the walking belt is properly tight-

 

ened.

 

 

 

c. If the walking belt still slows when walked on, see the front cover of this manual.

 

19

Image 19
Contents On the WEB QUESTIONS?Model No. GGTL03607.4 Serial No Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MTTable of Contents Important Precautions Treadmill is not in use. See the drawing on Before YOU Begin Assembly Do not fully fold the Frame yet Make sure that the power cord is unpluggedNot overtighten the Nut the Wheel must turn Freely Do not fully tighten the Bolts yet Upright Spacer 80. Be careful not to pinch96mm Bolts 5 do not fully tighten Bolts yet Not fully fold the Frame yetPage Page HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Features of the Console Console DiagramFollow your progress with the display HOW to Turn on the PowerHOW to USE the Manual Mode Insert the key into the consoleTurn on the fan if desired Measure your heart rate if desiredPress the Start button to start the workout HOW to USE a Classic WorkoutSelect a weight loss workout HOW to USE the Weight Loss WorkoutInformation Mode HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingCompatible with GFCI-equipped outlets Top Problem The walking belt slows when walked onProblem Solution Exercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesKey No. Qty Description Part LIST-Model No. GGTL03607.4Key No. Qty Description Exploded Drawing A-Model No. GGTL03607.4 R1008A Exploded Drawing B-Model No. GGTL03607.4 R1008A Exploded Drawing C-Model No. GGTL03607.4 R1008A Exploded Drawing D-Model No. GGTL03607.4 R1008A Limited Warranty Ordering Replacement PartsIcon Health & Fitness, Inc., 1500 S W., Logan, UT