Gold's Gym GGTL03607.4 manual

Page 9

7.Attach the Latch Insert (70) to the Left Upright (73) with two #10 x 1" Tek Screws (76). Make sure that the large hole in the Latch Insert is on the side shown. Do not overtighten the Tek Screws.

Locate the Latch Pin Assembly (72). Remove the knob from the pin. Make sure that the collar and the spring are on the pin as shown. Insert the pin into the Latch Insert (70), and tighten the knob back onto the pin.

7

72

70

 

73

Knob

76

 

 

Collar

 

 

Spring

Pin

Large Hole

8.Hold the Right Handrail (90) near the Right Upright (78). Insert the Upright Wire (77) into the opening in the bot- tom of the Right Handrail and out of the indicated hole in the top.

Set the Right Handrail (90) on the Right Upright (78), and finger tighten three M8 x 19mm Bolts (6) with three M8 Star Washers (10) into the Right Handrail and the Right Upright. Do not fully tighten the Bolts yet. Make sure that the Upright Wire (77) is not pinched. Attach the Left Handrail (89) to the Left Upright (73) as described above. Note: There are no wires on the left side.

9.Have another person hold the console assembly near the Right Handrail (90). Attach the end of the ground wire to the indicated small hole in the Right Handrail with the M4.2 x 13mm Silver Screw (4).

Connect the Upright Wire (77) to the console wire. See the inset drawing. The connectors should slide to- gether easily and snap into place. If they do not, turn one connector and try again. IF THE CONNECTORS

ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON.

Remove the wire tie from the Upright Wire (77).

8

 

89

 

 

 

 

 

 

77 Hole90

 

6

 

 

 

 

10

6

 

Wire Tie

 

 

73

6

10

6

 

 

 

 

 

10

 

 

 

 

 

 

 

 

 

 

 

78

 

9

Console

 

 

Console Assembly

 

 

4

 

Ground

 

 

Wire

 

 

Wire

 

 

77

 

 

 

Small Hole

 

 

 

 

90

Console

 

 

 

 

Wire

Wire

 

 

 

 

 

 

 

 

 

Tie

77

 

 

 

 

 

 

 

9

Image 9
Contents Model No. GGTL03607.4 Serial No QUESTIONS?Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT On the WEBTable of Contents Important Precautions Treadmill is not in use. See the drawing on Before YOU Begin Assembly Make sure that the power cord is unplugged Do not fully fold the Frame yetNot overtighten the Nut the Wheel must turn Freely 96mm Bolts 5 do not fully tighten Bolts yet Upright Spacer 80. Be careful not to pinchNot fully fold the Frame yet Do not fully tighten the Bolts yetPage Page Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerInsert the key into the console Follow your progress with the displayTurn on the fan if desired Measure your heart rate if desiredPress the Start button to start the workout HOW to USE a Classic WorkoutHOW to USE the Weight Loss Workout Select a weight loss workoutInformation Mode HOW to Fold and Move the Treadmill HOW to Move the TreadmillHOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useCompatible with GFCI-equipped outlets Top Problem The walking belt slows when walked onProblem Solution Exercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencyKey No. Qty Description Part LIST-Model No. GGTL03607.4Key No. Qty Description Exploded Drawing A-Model No. GGTL03607.4 R1008A Exploded Drawing B-Model No. GGTL03607.4 R1008A Exploded Drawing C-Model No. GGTL03607.4 R1008A Exploded Drawing D-Model No. GGTL03607.4 R1008A Ordering Replacement Parts Limited WarrantyIcon Health & Fitness, Inc., 1500 S W., Logan, UT