Gold's Gym GGTL03607.4 Upright Spacer 80. Be careful not to pinch, Not fully fold the Frame yet

Page 8

4. Hold a Bolt Spacer (79) inside the lower end of

4

 

 

 

 

 

 

the Right Upright (78). Insert an M10 x 96mm

 

 

5

 

 

 

Bolt (5) with an M10 Star Washer (8) into the

 

78

 

 

 

 

Right Upright and the Bolt Spacer. Repeat this

 

 

 

 

 

 

step with a second Bolt Spacer (79), M10 x

 

 

 

 

 

 

 

96mm Bolt (5), and M10 Star Washer (8).

 

 

 

 

8

77

79

Hold the Right Upright (78) against the Right

 

 

 

 

Upright Spacer (80). Be careful not to pinch

 

 

 

 

 

 

 

the Upright Wire (77). Partially tighten the M10

 

 

 

 

 

79

82

x 96mm Bolts (5); do not fully tighten the

 

 

 

 

80

Bolts yet.

 

 

 

 

 

 

Press a Base Endcap (82) into the Base (85).

 

 

 

 

85

 

5. With the help of a second person, carefully tip

5

 

 

 

 

 

 

the treadmill onto its right side. Partially fold the

 

 

 

 

 

 

Frame (48) so the treadmill is more stable; do

 

 

 

 

 

 

 

not fully fold the Frame yet.

2 81

 

 

 

48

 

 

Attach a Base Pad (81) to the Base (85) in the

 

 

 

 

 

location shown with an M4.2 x 25mm Tek Screw

 

 

 

 

 

 

27

(2) and a Base Pad Spacer (64). Then, attach

 

 

 

 

 

 

another Base Pad (81) with only an M4.2 x

85

 

64

 

 

 

 

25mm Tek Screw (2).

 

 

 

 

 

Attach a Wheel (86) to the Base (85) with an

 

 

 

 

86

 

 

M10 x 50mm Bolt (27) and an M10 Nut (33). Do

 

 

2

81

33

 

not overtighten the Nut; the Wheel must turn

 

 

 

 

freely.

 

 

 

 

 

 

 

6. Have a second person hold a Bolt Spacer (79)

6

 

 

 

 

 

 

inside the lower end of the Left Upright (73).

 

 

 

 

 

 

Insert an M10 x 96mm Bolt (5) with an M10 Star

 

 

 

 

 

73

 

Washer (8) into the Left Upright and the Bolt

 

5

83

 

 

 

Spacer. Repeat this step with a second Bolt

 

 

 

 

 

Spacer (79), M10 x 96mm Bolt (5), and M10

79

8

 

 

 

 

 

Star Washer (8).

 

 

 

 

 

Orient the Left Upright (73) and the Left Upright

 

 

 

 

 

 

 

Spacer (83) as shown. Hold the Left Upright

82

79

 

 

 

 

 

Spacer and the Left Upright against the Base

 

 

 

 

 

(85). Partially tighten the M10 x 96mm Bolts (5);

 

85

 

 

 

 

 

do not fully tighten the Bolts yet.

 

 

 

 

 

 

Press a Base Endcap (82) into the Base (85).

 

 

 

 

 

 

 

With the help of a second person, tip the tread-

 

 

 

 

 

 

 

mill so that the Base (85) is flat on the floor.

 

 

 

 

 

 

 

 

8

 

 

 

 

 

 

Image 8
Contents QUESTIONS? Model No. GGTL03607.4 Serial NoMon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT On the WEBTable of Contents Important Precautions Treadmill is not in use. See the drawing on Before YOU Begin Assembly Not overtighten the Nut the Wheel must turn Freely Make sure that the power cord is unpluggedDo not fully fold the Frame yet Upright Spacer 80. Be careful not to pinch 96mm Bolts 5 do not fully tighten Bolts yetNot fully fold the Frame yet Do not fully tighten the Bolts yetPage Page PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeInsert the key into the console Follow your progress with the displayMeasure your heart rate if desired Turn on the fan if desiredHOW to USE a Classic Workout Press the Start button to start the workoutInformation Mode HOW to USE the Weight Loss WorkoutSelect a weight loss workout HOW to Lower the Treadmill for USE HOW to Fold and Move the TreadmillHOW to Move the Treadmill Compatible with GFCI-equipped outlets TroubleshootingProblem The power turns off during use Problem The walking belt slows when walked on TopProblem Solution Exercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencyPart LIST-Model No. GGTL03607.4 Key No. Qty DescriptionKey No. Qty Description Exploded Drawing A-Model No. GGTL03607.4 R1008A Exploded Drawing B-Model No. GGTL03607.4 R1008A Exploded Drawing C-Model No. GGTL03607.4 R1008A Exploded Drawing D-Model No. GGTL03607.4 R1008A Icon Health & Fitness, Inc., 1500 S W., Logan, UT Ordering Replacement PartsLimited Warranty