Healthrider HMTL79608.0 manual Troubleshooting, Important The treadmill is not

Page 22

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and

follow the steps listed. If further assistance is needed, see the front cover of this manual.

 

PROBLEM: The power does not turn on

 

 

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor

is plugged into a properly grounded outlet (see page 11). Use only a single-outlet surge suppres-

sor that meets all of the specifications described on page 11.

IMPORTANT: The treadmill is not

compatible with GFCI-equipped outlets.

 

 

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c. Check the reset/off circuit breaker located on the

c

 

treadmill frame near the power cord. If the switch pro-

 

trudes as shown, the circuit breaker has tripped. To

 

 

reset the circuit breaker, wait for five minutes and

Tripped

Reset

then press the switch to the reset position.

PROBLEM: The power turns off during use

 

 

SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait

for five minutes and then press the switch to the reset position.

 

b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five

minutes, and then plug it back in.

 

 

c. Remove the key from the console. Reinsert the key into the console.

 

d. If the treadmill still will not run, see the front cover of this manual.

 

PROBLEM: The displays of the console do not function properly

 

 

SOLUTION: a. Remove the key from the console and UNPLUG THE

a

 

POWER CORD. Next, carefully lower the Uprights

 

(111, 113). Remove the two indicated #8 x 3/4"

 

 

Screws (6). Note: A Phillips screwdriver with a shaft at

 

 

least 8 in. (20 cm) long is needed.

 

 

 

111

6

 

 

Raise the Uprights (111, 113) to the vertical position.

 

 

113

Remove the three #8 x 3/4" Screws (6) from the Motor

111

6

Hood (33), and carefully pivot the Motor Hood off.

 

 

33

 

 

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents QUESTIONS? Model No. HMTL79608.0 Serial NoTable of Contents Various factors, including the users move Important PrecautionsMent, may affect the accuracy of heart rate Page Before YOU Begin Assembly Make sure that the power cord is unpluggedPage Page Wire Harnesses 73, 119 are not pinched Pull on the sleeve to make sure that it is Locked into placeHOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Features of the Console HOW to Turn on the Power Time/Pace Calories/Pulse dis- -This display willSpeed display Measure your heart rate if desiredSelect a classic workout HOW to USE a Classic WorkoutInsert the key into the console Follow your progress with the matrix and the displaysEnter your weight Select a weight loss workoutHOW to Create a Custom Workout HOW to USE a Custom Workout Information Mode HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USEImportant The treadmill is not TroubleshootingProblem The power turns off during use Compatible with GFCI-equipped outletsWalking belt slows when walked on Problem SolutionTop Problem Solution Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencyPart LIST-Model No. HMTL79608.0 Qty DescriptionQty Exploded Drawing A-Model No. HMTL79608.0 R1108A Exploded Drawing B-Model No. HMTL79608.0 Exploded Drawing C-Model No. HMTL79608.0 R1108A Exploded Drawing D-Model No. HMTL79608.0 R1108A Ordering Replacement Parts
Top Page Image Contents