Healthrider HRT99020 manual Magnet is aligned with the Reed Switch, Switch is about 1/8

Page 24

Locate the Reed Switch (18) and the Magnet (101) on

the left side of the Pulley (78). Turn the Pulley until the

Magnet is aligned with the Reed Switch.

Make sure

that the gap between the Magnet and the Reed

 

Switch is about 1/8”.

If necessary, loosen the 3/4”

Screw (24) and move the Reed Switch slightly. Retighten the Screw. Re-attach the hood, and run the treadmill for a few minutes to check for a correct speed reading.

PROBLEM: The walking belt slows when walked on

1/8”

78

24

 

18

101

Top

 

View

 

SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 8.

b. If the walking belt is overtightened, treadmill perfor- mance may decrease and the walking belt may be-

come damaged. Remove the key andUNPLUG THE

POWER CORD . Using the allen wrench, turn both rear roller adjustment bolts counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each side of the walking belt 3 to 4 inches off the walking platform. Be careful to keep the walking belt centered. Plug in the power cord, in- sert the key, and run the treadmill for a few minutes. Repeat until the walking belt is properly tightened.

b

3”–4”

Rear Roller Adjustment Bolts

c. If the walking belt still slows when walked on, call our Customer Service Department toll-free.

PROBLEM: The walking belt is off-center or slips when walked on

SOLUTION: a. If the walking belt is off-center, remove the key and

 

UNPLUG THE POWER CORD

. If the walking belt

has shifted to the left,

use the allen wrench to turn

 

the left rear roller bolt clockwise 1/2 of a turn;

if the

walking belt has shifted to the right,

turn the bolt

counterclockwise 1/2 of a turn. Be careful not to over-

 

tighten the walking belt. Plug in the power cord, insert

 

the key, and run the treadmill for a few minutes.

 

Repeat until the walking belt is centered.

 

b. If the walking belt slips when walked on, remove the

key and UNPLUG THE POWER CORD . Using the allen wrench, turn both rear roller bolts clockwise, 1/4

of a turn. When the walking belt is correctly tightened, you should be able to lift each side of the walking belt 3 to 4 inches off the walking platform. Be careful to keep the walking belt centered. Plug in the power

cord, insert the key, and carefully walk on the tread- mill for a few minutes. Repeat until the walking belt is properly tightened.

a

b

PROBLEM: The incline of the treadmill does not change correctly or does not change when iFIT.com

CD’s and videos are played

 

 

SOLUTION: a. With the key inserted in the console, press one of the Incline buttons.

While the incline is

changing, remove the key.

After a few seconds, re-insert the key. The treadmill will automati-

cally rise to the maximum incline level and then return to the minimum level. This will recalibrate

 

the incline.

 

 

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents QUESTIONS? Model No. HRT99020 Serial NoOur factory Customer HOT LineTable of Contents Important Precautions Use the treadmill only as describedTreadmill is capable of high speeds Page Using the treadmill Before YOU BeginAssembly Assembly requires two peopleDriver Wire cutters Insert the other Extension Leg not shown in the same wayInsert two 1/2 Screws 33 into Screws 105 as shownTightly as possible PostHOW to Plug in the Power Cord Performant LubeThis product must be grounded.If it should malfunc Grounded Outlet Box Surge Suppressor Grounding PinConsole Diagram Features of the ConsoleTo reduce the possibility of electric shock HOW to Turn on the Power HOW to USE the Manual ModeWhen the treadmill is folded to the storage posi Time/Incline/SegmentDistance/Laps Display Speed/Min-Mile DisplayHOW to USE Personal Trainer Programs Completed, all speed settings will move one colStart the program Program displayHOW to USE Heart Rate Programs Follow your progress with the displaysPut on the chest pulse sensor Select a heart rate programWhen the program is completed, remove Key from the console Enter your ageDecrease HOW to Connect Your Portable CD Player HOW to Connect Your Portable StereoVideocassettes HOW to Connect Your Home Stereo HOW to Connect Your ComputerJack on your stereo Adapter CableHOW to Connect Your VCR Next settings of the CD or video program When you are finished using themTon or the Speed Whenkey. the program is completed, removeHOW to USE Programs Directly from OUR WEB Site Followprogram.the on-line instructions to startConsole SpeedInformation MODE/DEMO Mode Play should be blank If a dButtons on the console will not operate If a d ap Optional Chest Pulse SensorHOW to Fold the Treadmill for Storage HOW to Move the TreadmillHOW to Lower the Treadmill for USE Hold the upper end of the treadmill with your right handHold the treadmill firmly with both hands, and lower Pin CatchTroubleshooting Problem The power does not turn onProblem The power turns off during use PositionMagnet is aligned with the Reed Switch Switch is about 1/8Problem The walking belt slows when walked on Has shifted to the leftConditioning Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencySuggested Stretches Page HOW to Order Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT Part No R1102ARemove this Exploded Drawing and Part List from the Manual Key Description No. Qty. DescriptionKey No. Qty. Description Drawingexploded Model
Top Page Image Contents