Healthrider HCTL06190 manual Problemsolution, Walking belt is off-center or slips when walked on

Page 17

PROBLEMSOLUTION

5.The walking belt is off-center or slips when walked on

a. If the walking belt has shifted to the

 

 

 

 

 

a

 

 

left, first remove the key and UNPLUG

 

 

 

 

 

 

 

THE POWER CORD. Using the allen

 

 

 

 

wrench, turn the left rear roller adjustment

 

 

 

 

bolt clockwise, and the right bolt counter-

 

 

 

 

clockwise, 1/4 of a turn each. Be careful

 

 

 

 

not to overtighten the walking belt. Plug in

 

 

 

 

the power cord, insert the key and run the

 

 

 

 

treadmill for a few minutes. Repeat until the walking belt is centered.

b. If the walking belt has shifted to the right,

 

 

 

 

 

b

 

first remove the key and UNPLUG THE

 

 

 

 

 

 

 

 

 

 

POWER CORD. Using the allen wrench,

 

 

 

 

turn the left rear roller adjustment bolt

 

 

 

 

counterclockwise, and the right bolt clock-

 

 

 

 

wise, 1/4 of a turn each. Be careful not to

 

 

 

 

overtighten the walking belt. Plug in the

 

 

 

 

power cord, insert the key and run the

 

 

 

 

treadmill for a few minutes. Repeat until the walking belt is centered.

c. If the walking belt slips when walked on,

 

 

 

 

 

c

 

 

first remove the key and UNPLUG THE

 

 

 

 

 

 

POWER CORD. Using the allen wrench,

 

 

 

 

turn both rear roller adjustment bolts clock-

 

 

 

 

wise, 1/4 of a turn. When the walking belt

 

 

 

 

is correctly tightened, you should be able

 

 

 

 

to lift the edges of the walking belt 3 to 4

 

 

 

 

inches off the walking platform. Be careful

 

 

 

 

to keep the walking belt centered. Plug in the power cord, insert the key and run the treadmill for a few minutes. Repeat until the walking belt is properly tightened.

6.An error code (“E1,” “E2,” “E3,” or “E4,”) appears in the SPEED display

a.If error code “E1,” “E2,” or “E3” appears in the SPEED display, remove the key, wait for ten seconds, and then reinsert it. If the error code appears again, call our Customer Service Department. Do not operate the treadmill until the problem is corrected.

b.Error code “E4” may appear in the SPEED display if the walking belt is moving at a slow speed and there is excessive stress on the motor. If this occurs, remove the key, wait for ten seconds, and then reinsert it. If you weigh over 200 pounds, it may also be helpful to increase the incline of the treadmill. If the error code appears again, call our Customer Service Department. Do not operate the tread- mill until the problem is corrected.

7. The walking belt

a. Use a color-fast upholstery cleaner to clean the walking belt. Test the

becomes soiled

cleaner on a small area before cleaning the entire belt.

8.Bubbles form in the walking belt

a.Due to variations in humidity and temperature, there is a possibility that bubbles may form in the walking belt. Although the bubbles will disappear with time, you may unplug the power cord, carefully insert a needle into the bubbles, and push the air out of the bubbles.

17

Image 17
Contents Customer HOT Line QUESTIONS?Model No. HCTL06190 Serial No Table of Contents Important Precautions Decal above is shown at 75% of actual size Back Right Side Before YOU BeginSetting UP the Treadmill Performant Lubetm Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Operation Features of the ConsoleRefer to the drawing at the top Diagram of the ConsoleHOW to Turn on the Power Select the manual mode HOW to USE the Manual ModeInsert the key into the console Change the incline of the treadmill as desiredDISTANCE/INCLINE HOW to USE the Speed Programs and the Incline ProgramCALORIES/FAT Insert the key fully into the consoleWhenkey. you are finished exercising, remove Follow your progress with the four displaysInformation Mode HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USE TROUBLE-SHOOTING and MaintenanceProblem Solution Power doesMagnet and the Reed Switch is about Power turnsOff during use DisplaysWalking belt is off-center or slips when walked on ProblemsolutionBecomes soiled Bubbles form in the walking beltConditioning Guidelines HOW to Measure YOU Heart RateExercise Intensity Workout GuidelinesSuggested Stretches Key No. Qty Description Part LIST-Model No. HCTL06190Ordering Replacement Parts Exploded Icon of CANADA, 900 de l’Industrie, St. Jerôme, QC J7Y 4B8 Limited Warranty