Tunturi T70 owner manual Memory Function, Maintenance

Page 11

MEMORY FUNCTION

The Memory function requires the use of a user code: the exercise is saved under the selected user code. You can save 5 exercises under each user code.

SAVING YOUR OWN PROFILE:

1.You can save preset profiles once the exercise is completed, or after finishing the exercise by pressing

STOP once. If you want to save your Manual or HRC workouts, finish the exercise by pressing STOP once.

Save your exercise by pressing MEM.

2.The display prompts for a memory slot (SAVE AS OWN 1-5). Select the desired memory slot with the jogwheel and press JOGWHEEL to confirm your selection: your workout is now saved to the desired slot.

3.If there are no empty memory slots, replace a previous profile with a new one. The display then prompts you

to confirm (REPLACE OWN 1-5). Press JOGWHEEL to confirm your selection: your workout is now saved to the desired slot.

4.SAVED AS OWN 1-5 is displayed to confirm your

save. The console will automatically switch to its initial state.

NOTE! To save a profile, you need to exercise for 10 minutes or more.

USING YOUR OWN PROFILE:

1.Select your user code.

2.Press MEM.

3.Use JOGWHEEL until the signal light indicates the desired own profile (-1-5 MEMORY). Press JOGWHEEL to confirm your selection. Select RERUN (to use the profile without adjustments) or RACE (to use the profile as a basis for the

Race function) with the JOGWHEEL key.

4.Press JOGWHEEL to confirm your selection.

5.Press START to begin the profile.

6.The RERUN function allows you to scale your own profile and save the changes.

RACE FUNCTION

To race against a previously saved exercise, select RACE in the Own Profile menu.

1.Press START. The exercise begins and the belt starts moving.

2.Adjust the speed according to your fitness level either manually or using the PSC function.

3.The console display shows information on profile progress and any changes ahead.

4.Once the profile has been completed, the cool-down period will automatically start. You can save your workout in the console’s memory (see Memory Function).

MAINTENANCE

The equipment is safe to use only when periodically maintained and inspected for faults and wear. Do not attempt any servicing or adjustment other than those described in this manual. Any other servicing must be performed by an authorized service representative. Check the tightness of all fixing screws once a year. Do not overtighten. Defective components must be immediately replaced: the equipment must not be operated with any defective components.

CLEANING AND LUBRICATING THE TREADMILL

FAILURE TO LUBRICATE YOUR TREADMILL MAY INVALIDATE THE PRODUCT’S WARRANTY!

Wipe the treadmill surfaces, especially the handlebars and console from dust with a damp cloth or towel. Do not use solvents. Use a small vacuum nozzle to carefully vacuum around all visible components (belt, running deck, side rails etc.). Also keep the area near the treadmill clean. While in use, the treadmill gathers dust that may cause problems in the operation of the equipment.

In average domestic use (a maximum of 60 minutes a day), you should check the lubrication once a month

however, lubricate the belt only if needed. In more demanding use, the lubrication needs be checked at shorter intervals. This is best done before you begin a training session. Check the lubrication as follows:

1. Ensure the treadmill is powered off! Step on the treadmill belt and stand steadily where you normally run on the belt.

2. Take hold of the horizontal handlebar and push the belt with your feet so that it slides back and forth. The belt should move softly and evenly, without a sound. 3. If you notice jerky movement or if the belt will not slide check for lubrication by sliding your hand under the belt. Lubricate the running deck according to the following instructions:

NOTE! Lubricate your treadmill only with T-Lube S silicon lubricant. Contact your local Tunturi distributor for further supplies of T-Lube or further information on lubrication and maintenance.

IMPORTANT! Treadmills need constant lubrication. After not using the machine for a while, the deck could dry out and needs to be lubricated. Make sure you check after long periods if the belt needs lubrication. To lubricate open the small caps at the end of the treadmill with a small coin. And squeeze half the bottle of T-lube. The lubrication system will make sure the belt is evenly lubricated.

11

 

T70 & T80 - OWNER’S MANUAL

ENGLISH

Image 11
Contents T70 & T80 Contents Handlebar and Console T70/T80Upright Tubes About the Exercise Environment Safety KEYPower Cord and Grounding Instructions Basics on ExercisingFinishing AN Exercise Session About Using the EquipmentHeart Rate Beginning AN Exercise SessionGraphic / Text Display ConsoleFunction Keys DisplaysTraining with PSC PSC SettingsPosition Speed Control PSC Choosing AN ExerciseHeart Rate Controlled Exercise Manual ExerciseBeginning the Cooper Test Exercise ProfilesCooper Test Performing the Cooper TestProfiles Memory Function MaintenanceMoving Storage Adjusting the Belt TensionError Codes Malfunctions13,7 mph Technical DataConseils et avertissements Conseils et avertissementsBienvenue Dans LE Monde DE ’ENTRAINEMENT Tunturi Guidon ET Console Emballage 1/2Emballage 2/2 Tubes VerticauxCordon D’ALIMENTATION CLE DE Verrouillage DE SecuriteGénéralités SUR L’ENTRAÎNEMENT Touches DE Fonction Touche DE Commande D’INCLINAISONRythme Cardiaque Unite DES CompteursRéglage DES Données Utilisateur AffichagesGRAPHISME/AFFICHAGE DE Texte Training Avec LA Fonction PSC Choisissez le mode d ’entraînement Manual, RollingVitesse Contrôlée PAR POSITIONNE- Ment PSC Quick Start Démarrage Rapide Choix DE L’ENTRAINEMENTManual ENTRAINE- Ment Manuel Entrainement PAR Controle DE LA FRE- Quence CardiaqueTest DE Cooper Profils D’ENTRAINEMENTTest DE Condition Physique LE Test DE Marche 2 KMAGE Enregistrement DE VOS Propres Profils ProfilsFonctions DE LA Mémoire Nettoyage DE L’APPAREIL ET Graissage DE LA Plaque DE Base Utilisation DE Votre Propre ProfilFonction Compétition EntretienCoder D’ERREUR Transport ET RangementReglage DE LA Tension DU Tapis Defauts DE FonctionnementAngle d’inclinaison 12 % Moteur T70 T80 Caracteristiques Techniques105 102 M8x45 ISO FilterM13 DIN Washer Fixing tube M10 DIN Nut M8x42 ISO M8x55 DIN10TUT70000 10TUT80000 T70, T80 Exploided ViewN E R ’ S 108 M a N U a L