Image 831.100430 user manual Choosing a Location for the Renew, If you set up the Renew 900 inside

Page 7

CHOOSING A LOCATION FOR THE RENEW 900

There are many factors to consider when choosing a location to set up the RENEW 900. These factors vary depending on whether you use the RENEW 900 inside or outside. We have listed several factors you may wish to consider as you decide where you want to use the RENEW 900.

If you set up the RENEW 900 inside:

1.The RENEW 900 will increase the level of humidi- ty in your home. The location you choose should

be well ventilated. You may need to install a venti- lation fan or use a dehumidifier.

2.The location must be close to an electrical outlet.

Do not use an extension cord with the RENEW 900.

3.The RENEW 900 should be close to a source of

water.

4.Do not use the RENEW 900 on carpet or other material that may be damaged by moisture. We recommend that you place the RENEW 900 on a water- and stain-resistant, non-slip surface with a floor drain for any water that may splash from the RENEW 900.

5.Be sure that the location you choose is stable. It

must be able to support the weight of the RENEW

900 when it is filled with water, plus the weight of the occupants. The RENEW 900 weighs approxi- mately 2400 pounds when filled with water.

6.Do not use the RENEW 900 above a finished liv- ing area, due to the risk of water damage.

7.Be sure that there is room around the RENEW

900 to permit servicing of the unit. The diameter of

the tub is 69”. You should allow for this size, plus the size of the spa jet unit, when choosing the location.

8.Be sure to note any other considerations, such as aesthetics or privacy concerns, that may affect the safety or enjoyment of using the RENEW 900.

If you set up the RENEW 900 outside:

1.You should check your local building codes con- cerning the use of outdoor spas.

2.The location must be close to an electrical outlet.

Do not use an extension cord with the RENEW 900.

3.The RENEW 900 should be close to a source of water.

4.We recommend that you place the RENEW 900

on a water- and stain-resistant, non-slip surface.

5.Be sure that the location you choose is stable. It must be able to support the weight of the RENEW

900 when it is filled with water, plus the weight of the occupants. The RENEW 900 weighs approxi- mately 2400 pounds when filled with water.

6.Think about environmental factors, such as rain, wind, shade, sunlight, and so forth.

7.You should be able to monitor the use of the RENEW 900 from your home, to prevent unautho- rized use by children.

8.Be sure that there is room around the RENEW

900 to permit servicing of the unit. The diameter of

the tub is 69”. You should allow for this size, plus the size of the spa jet unit, when choosing the location.

9.Be sure to note any other considerations, such as aesthetics or privacy concerns, which may affect the safety or enjoyment of using the RENEW 900.

7

Image 7
Contents Sears CANADA, INC., TORONTO, Ontario M5B 2B8 QUESTIONS?Model No Serial No Customer HOT LineTable of Contents Use the Renew 900 only as described in this manual Important Safety InstructionsWater pump in the spa jet unit must be Hol or drugs can cause unconsciousness Keep pets away from the Renew 900 at all timesContact a physician Image Before YOU Begin Do not use an extension cord with the Renew If you set up the Renew 900 insideIf you set up the Renew 900 outside Choosing a Location for the RenewBuckle Slot AssemblyBefore beginning assembly, carefully read Following information and instructionsLatches and Buckles BucklePlugging in the Renew Using the RenewTesting and Treating the Water Priming the SPA JET UnitJet Diagram of the Console Using the ConsoleSecuring the SPA Cover Latch Buckle KeyDraining the Renew SPA JET Unit OperationDraining the Pump Maintenance Symptom the Water Pulsates or There is Minimum Water Flow Symptom the SPA will not OperateSymptom the Pump Hums Symptom the Water does not HeatCare on Symptom the SPA JET Unit ContinuesPower cord must be unplugged Symptom the Water Level DropsModel Number of the product Name of the product Image Ordering Replacement PartsDe l’Industrie St-Jérôme, Québec Canada, J7Y 4B8 Customer RecordModel No Serial No DateProduct Warranty Registration Limited Five Year Massage SPA WarrantyDu Modèle De Série References’Achat Formulaire DE Garantie DU Produit Garantie Limitée DE Cinq ANSKey No. Qty Description Part LIST-Model NoR0499A 100430