Cateye CC-TR200DW (V2c) instruction manual How to install the unit on your bicycle

Page 4

How to install the unit on your bicycle

1. Attach the bracket to the stem or handlebar

The Flex Tight ™ bracket can be attached to either the stem or the handlebar depend- ing on how the bracket and band are configured.

Caution:

Tighten the dial on the bracket band by hand only.

Over-tightening can damage the screw threads.

When attaching the Flex Tight ™ bracket to the stem

* Attach the bracket with its open end facing to the right.

Bracket band

Bracket rubber pad Stem

2. Mount the speed sensor and magnet

Speed sensor

Wheel magnet

 

SPEED

 

CADE

 

NCE

Cadence magnet

ENG

Bracket

2-1. Temporarily secure the speed sensor

Locate the speed sensor on the left chain stay as shown above, and loosely secure it with the nylon ties.

*Do not tighten the nylon ties completely at this stage. Once a nylon tie is tightened, it cannot be pulled out.

Speed sensor

SPEED

When attaching the Flex Tight ™ bracket to the handlebar

* Attach the bracket with its open end facing to the right.

Bracket band

Handlebar

Bracket rubber pad

Bracket

 

 

Nylon ties

 

2-2. Mount the magnet

 

 

1.

Loosen the setscrews both on the SPEED side

Wheel

 

 

and CADENCE side of the speed sensor, and turn

magnet

 

 

the sensor to the angle as shown on the right.

 

 

2.

Temporarily secure the wheel magnet to the

Setscrew on the

 

 

spoke so that it faces the sensor zone on the

CADENCE side

 

 

SPEED side.

 

SPEED

3.

Temporarily secure the cadence magnet inside Sensor zone

 

 

the crank with nylon ties, so that it faces the

CADENCE

Sensor

 

sensor zone on the CADENCE side.

 

zone

Cut extra length of the band with scissors.

Caution:

Round off the cut edge of the bracket band to prevent injury.

*When the speed sensor is not positioned ap- propriately in respect to the two magnets (in both Steps 2 and 3), move the speed sensor back and forth so that it is positioned properly. After you move the speed sensor, adjust the position so that the two magnets face the rel- evant sensor zone.

4.After adjustment, tighten the nylon ties firmly to secure the speed sensor.

Setscrew on the

SPEED side

Cadence

magnet

Nylon ties

ENG-6

Continue

ENG-7

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Introduction About the manualsContents Proper use of the CatEye V2cDescription of computer and its parts Screen display AccessoriesComputer Attach the bracket to the stem or handlebar How to install the unit on your bicycleMount the speed sensor and magnet Remove/install the computer Preparing the computerDate/Clock setting Formatting/Restarting operation24h ↔ 12h ENG-10How to measure the tire circumference L Tire circumference inputSet the sensor ID Tire circumferenceBasic operation of the computer Selecting speed unitOperation test Functions on the measurement screenResetting the measurement data Power-saving functionMeasurement screen Starting/Stopping the measurementPace function Lower display dataLap function Target cadence zone Countdown distanceLap time and split time Advance use of the real time lap dataChanging the computer configuration File viewMeasurement data to be recorded in a file Date of creation New OldViewing the lap data ENG-24Setting the clock/date Switching the file numberDeleting files ENG-26Wheel selection and tire circumference Searching the sensor ID↔ B ENG-28Setting the measurement unit Setting the auto-modeSetting the countdown distance Total distance manual entrySetting sound CDC.ALARM ↔ BUTTOnOn ↔ OFF M1/+M2/- or ENG-32Trouble shooting Use of the target zoneCadence zone Trouble on displayReplacing battery Trouble on operationSpeed sensor ENG-36Maintenance Spare accessoriesSpecifications Standard accessoriesLimited warranty RegistrationYear computer, and speed sensor Not including depletion of batteries
Top Page Image Contents