Cateye CC-TR200DW (V2c) instruction manual Preparing the computer, Remove/install the computer

Page 5

2-3. Adjust the distance to the magnet

1. Adjust the distance between the wheel magnet and the SPEED side of the speed sensor to be about 3 mm. After adjustment, tighten the setscrew on the SPEED side.

2. Adjust the distance between the cadence

About 3 mm

 

magnet and the CADENCE side of the speed

 

 

 

sensor to be about 3 mm. After adjustment,

 

 

tighten the setscrew on the CADENCE side. SPEED

Wheel

CADENCE

magnet

 

Cadence magnet

About 3 mm

 

 

 

2-4. Securing various parts

Preparing the computer

Computer's basic items must be set up before using it.

 

 

Removing the insulation sheet

 

Close

When using the unit for the first time after purchas-

 

Insulation

ing, open the battery cover and remove the insula-

Open

tion sheet.

sheet

* After you remove the insulation sheet, replace the battery cover in place.

Flow of set-up

There are 2 different set-up operations:

Formatting operation: At initial purchase, or reset all to default.

Restarting operation: When you replace batteries, or an error is displayed. Each operation has a different flow of set-up.

ENG

Tighten the speed sensor, setscrew, and magnet firmly, and check for any looseness.

*For steel axle pedals, cadence magnet can be compacly installed onto the end face of the pedal axle. Make sure to remove the double- sided tape from the magnet when doing this.

Cut extra length of the nylon tie with scissors.

For formatting:

Formatting operation

Date/clock setting

Tire circumference input

For restarting:

Restarting operation

Date/clock setting

* The date when you per-

formed the restarting

operation will be initially

In the restarting operation, the following data are re- tained.

Measurement screen

Total time

Total distance

Menu screen

File data saved

Time format

3. Remove/install the computer

Caution:

When removing, hold the unit to prevent it from falling.

Install

Remove

Holding the unit

 

 

Set the sensor ID

Selecting speed unit

displayed.

Date

Tire circumference and wheel selection

Speed unit Sensor ID Auto-mode Countdown distance

Slide the computer from the right

Measurement screen

Sound

Setting the target zone

Click

Push outward

*If mistake was made or ID-ERROR showed in the initial set up, go through the full initial set up steps first, and all corrections can be made afterwords through Menu screens. (page 22)

ENG-8

Continue

ENG-9

Image 5
Contents About the manuals IntroductionProper use of the CatEye V2c ContentsComputer AccessoriesDescription of computer and its parts Screen display Mount the speed sensor and magnet How to install the unit on your bicycleAttach the bracket to the stem or handlebar Preparing the computer Remove/install the computerFormatting/Restarting operation Date/Clock setting24h ↔ 12h ENG-10Tire circumference input How to measure the tire circumference LSet the sensor ID Tire circumferenceSelecting speed unit Basic operation of the computerOperation test Functions on the measurement screenPower-saving function Resetting the measurement dataMeasurement screen Starting/Stopping the measurementLap function Lower display dataPace function Countdown distance Target cadence zoneLap time and split time Advance use of the real time lap dataFile view Changing the computer configurationMeasurement data to be recorded in a file Date of creation New OldENG-24 Viewing the lap dataSwitching the file number Setting the clock/dateDeleting files ENG-26Searching the sensor ID Wheel selection and tire circumference↔ B ENG-28Setting the auto-mode Setting the measurement unitSetting the countdown distance Total distance manual entryCDC.ALARM ↔ BUTTOn Setting soundOn ↔ OFF M1/+M2/- or ENG-32Use of the target zone Trouble shootingCadence zone Trouble on displayTrouble on operation Replacing batterySpeed sensor ENG-36Spare accessories MaintenanceSpecifications Standard accessoriesRegistration Limited warrantyYear computer, and speed sensor Not including depletion of batteries