Spalding 21196804 manual Parts List See Hardware Identifier

Page 3

PARTS LIST - See Hardware Identifier

Item

Qty.

Part No.

Description

Item

Qty.

Part No.

Description

1

1

908123

Top Pole Section

28

2

900183

Elevator Tube, Lower-Long

2

1

908125

Middle Pole Section

29

2

204838

Spring

3

1

908124

Bottom Pole Section

30

2

904807

Elevator Tube, Upper-Short

4

2

202800

Ground Sleeve

31

2

200874

Spacer, Metal .402 I.D. x .50 O.D. x 1.5

5

1

202801

Ground Sleeve Cap

32

1

 

Rim

6

1

204832

Bracket, Pole Mount

33

12*

201219

Smart Clip

7

2

203053

Carriage Bolt, 5/16-18 x 4 Long

34

1

 

Net

8

9*

203100

Hex Flange Nut, 5/16-18

35

1

201251

Label, Height Adjustment

9

4

206360

Bolt, Hex Head, 3/8-16 x 2-5/8 Long

36

1

203279

Anti-Skid Tape

10

4

203232

Washer, Metal, 3/4” O.D.

37

1

204855

Handle, Left

11

4

203063

Nut, Nylock, Hex Head, 3/8-16

38

1

204856

Handle, Right

12

2

204858

Spacer, Biscuit, Plastic

39

2

201683

Spacer, Black, 1.5 Long

13

2

204857

Spacer, Metal 1/2” O.D. x 1.44 Long

40

1

206990

Bracket Reinforcement

14

2

204859

Cover, Spring

41

1

900033

Slam Jam Bracket, Black

15

1*

203038

Carriage Bolt, 5/16-18 x 2-3/4 Long

42

1

203796

Bolt, “Tee” 3/8 - NC x 5 Long

16

1

204850

Pin, Locking

43

1

200318

Bracket Reinforcement, Slam Jam

17

1

204853

Lanyard, Black Coil

44

1

203472

Spring, Black

18

1

908152

Height Adjustment Rod

45

1

203470

Washer, Flat 5/8 I.D. x 1-1/2 O.D.

19

1

204872

Label, Height Indicator

46

1

203795

Nut, Special 3/8-NC

20

2

203103

Carriage Bolt, 5/16-18 x 2 Long

47

4

205528

Bolt, Hex-Flange 5/16-18 x 1" Long

21

1

204803

Screw, Phillips Head

48

1

206118

Warning Label

22

4

202862

Spacer, .563 ID x 1.190 Long

49

1

903601

Rebar

23

4

206311

Spacer, .53 I.D. x .65 O.D. x .5 Long

50

2

204159

Rebar Centering Spacer

24

6

206340

Lock Nut,1/2-13

 

 

 

 

25

2

900964

Board Bracket

* YOU MAY HAVE EXTRA PARTS WITH THIS MODEL.

26

1

207103

Cap,Pole, 3.5" X .75"

 

 

 

 

27

6

206244

Bolt, Hex Head 1/2-13 x 8 Long

 

 

 

 

 

 

 

 

 

 

 

 

NOTICE TO ASSEMBLERS

ALL Huffy Sports Basketball Systems, including those used for DISPLAYS, MUST be assembled and ballasted with sand, water or concrete according to the instructions. Failure to follow instructions could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system.

IMPORTANT!

Remove all contents from boxes.

Be sure to check inside pole sections; hardware and additional parts are

packed inside.

WARRANTY CARD:

Please remember to complete your product registration form either on-line at: www.huffysports.com or mail-in the enclosed postcard.

For more information on assembly, placement, proper use, and maintenance, visit The American Basketball Council website at http://www.smarthoops.com.

3

10/04

P/N 21196804

Image 3
Contents Inground System Before YOU Start Parts List See Hardware Identifier Safety Instructions Hardware Identifier Bolts & Screws #22 Section a Assemble the Pole TOP Middle FIG. a Side View Keep Ground Sleeve CAP on Bottom Pole Label should be Front Side Tighten just until washers 10 stop moving Side Section B Assemble the Elevator Tubes to Backboard 10/04 As shown Container to Mix Phillips-Head Screwdriver 4 Wrenches 21196804 10/04 Install Slam Jam Rim to Backboard USE EYE Protection Reinforcement Bar 21196804 10/04 Install clips NET Installation None Playing Surface 10 ft 05 m