Precor EFX 833, EFX 883 warranty Installation Requirements, Hardware Kit not to scale, Fasteners

Page 16

14	Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 883 / 833

Begin installation of all fasteners by hand, then partially tighten them. Do not fully tighten fasteners until instructed to do so.

Important: When wrench-tightening the screws, make sure the head of the fastener is parallel to the product surface. If it is not, stop tightening to avoid cross-threading. To avoid further damage, stop assembly work and contact Customer Support.

Installation Requirements

Prior to assembly, make sure you have the required tools and hardware.

Hardware Kit (not to scale)

The hardware kit shipped with this equipment contains the fasteners and other hardware components shown in the following table. Before you begin assembly, make sure that your hardware kit is complete. If not, please contact Precor Customer Support.

Fasteners	Quantity
Flat washers (⁵₁₆-inch)	14

Split washers (⁵₁₆-inch)	14
Flat head hex drive screws	4
(¹₄-inch x ³₄-inch)
Phillips-head machine screws	3
(#8 x ³₄-inch)
Buttonhead screws (⁵₁₆–inch x�	14
1� –inch)

Image 16

Contents Assembling and Maintaining Elliptical Fitness Crosstrainers Page Page Trademark Note Edition InformationIntellectual Property Notice Important Safety Instructions Safety PrecautionsPage Educating Users Hazardous Materials and Proper Disposal Product Recycling and DisposalRegulatory Notices for the Rfid Module Radio Frequency Interference RFIFederal Communications Commission, Part Industry CanadaVoid the user’s authority to operate the equipment Débranchez avant de réparerSafety Approvals for Cardiovascular Equipment Regulatory Notices for Cardiovascular Exercise EquipmentEuropean Applications Cardiovascular Type EquipmentUser’s authority to operate the equipment Obtaining Service Obtaining Updated Documentation IEC-320 C13 and C14 plugsTable of Contents Commercial Cardiovascular Equipment Limited Warranty To prepare the EFX for assembly Assembling the EFXHardware Kit not to scale Installation RequirementsFasteners Assembling the EFX Performing the Assembly To begin assemblyIs properly installed Required ToolsRepeat steps 2 through 4 to attach the right upright support EFX cable path Cable connection points inside EFX base Lift cover replacement To mount the center column support on the frameTo tighten the fasteners properly Attachment of center column supportTighten the back fasteners on the upright supports To attach the handlebars Clamp screw location, EFX handlebar bracketTo tighten the handlebars completely Handrail attachment detailTo attach the water bottle holder Outer handrail caps attachmentTo attach the upright support covers Upright support cover attachment right-hand cover shownLeveling the EFX To level the unitBreaking in the Equipment Installing the Console Threading the Cable Assembly P80To thread the cable assembly Removing the access cover from the P80 consoleConnecting Cables P80 LocationCable Connector Type Circuit Location Connecting the Television CableTo connect the television cable Connecting the Ethernet and Base Unit Data Cables Connecting the television cableConnecting the Heart Rate Sensor Cable Connecting the Power CableCompleting the Console Installation P80 To complete the installationThreading the Cable Assembly P30 Connecting Cables P30 Verifying That the Heart Rate Display Is Operational Completing the Console Installation P30To verify that the heart rate display is operational Maintenance Daily CleaningDaily Inspection Weekly Maintenance Monthly MaintenanceMoving the Equipment Storing the Chest StrapLong-Term Storage Minimum requirements for operation Self-Powered FeaturesRate of Motion Symptoms of a Low Battery Informational Displays Prior to ShutdownUsing the Optional Power Adapter Optional Power Adapter KitReplacing the Battery Limited Warranty Commercial Cardiovascular Equipment Limited WarrantyWarranty Periods and Coverage Conditions and Restrictions Exclusive Remedies Exclusion of Consequential and Incidental Damages Complete this portion and keep for your recordsCommercial Cardiovascular Equipment Limited Warranty Page Page Precor Incorporated Operating and Maintaining the P30 Console Page Page Edition Information Important Safety Instructions Operating and Maintaining the P30 Console  Do not lean on or pull on the console at any time Hazardous Materials and Proper Disposal Regulatory Notices for Cardiovascular Exercise Equipment 240 V Equipment Designated for U.S. Markets 120-volt, 20-amp power plug 240-volt, 20-amp power plugOperating and Maintaining the P30 Console 240 V Equipment Designated Operating and Maintaining the P30 Console Activating the Console for Self-Powered Equipment Activating the Console for Self-Powered EquipmentGetting Started Optional Use of the Power Adapter Identifying Parts of the Console Number Part Name Details Watts Number Part Name Details Setting Up the Console System SettingsNavigational keys for the system setting modes Key To view the Club Parameters settings5 1 5 6 Setting Club Parameter Values Safety Code Treadmill onlySelect Language All Equipment Set Units All EquipmentSet Max Pause Time All Equipment Set Max Workout Time All EquipmentSet Cool Down Time All Equipment Creating a Custom Workout Value Range on or OFFTo create a custom program Custom Program keys Equipment Key Name DescriptionSet Incline Limit Treadmill only Set Speed Limit Treadmill onlyHidden Programs Treadmill only Set Crossramp Auto Level EFX Dual only Set Resistance Range Bike onlyValue Range 0 to To view the System settings Viewing the Informational DisplaysInformational Displays values Value Information providedEvent Log Product Value Information providedEvent Description of Event Number Csafe access keys Keys Function User ID Entry with Csafe EquipmentOperating and Maintaining the P30 Console Using the Touch Heart Rate Feature Introducing Users to the P30 ConsoleHeart rate target zones Using a Chest Strap Transmitter To use a chest strap transmitterInterfere with pacemakers or other Heart rate strapUsing the Treadmill Safety Clip Restart switchAttaching the safety clip Treadmill Auto Stop Automatic Stop Function Starting a Workout WORKOUT, Press QUICKSTART, or Enter to BeginStarting a Preset Programmed Workout Setting OptionsTo choose a language setting before you begin exercising To choose a workout goal before you begin exercisingTo enter your Age and Weight during a workout Setting Options after You Begin a WorkoutTo choose a unit of measure before you begin exercising Paused Externally Powered Equipment Pausing and Resuming an Exercise SessionPending Shutdown Self-Powered Equipment Ending a Session Operating and Maintaining the P30 Console Programs ManualHeart Rate IntervalVariety Weight LossPerformance Cleaning the Console and Display To remove dust and dirt from the console20031 142nd Avenue NE January Box Woodinville, WA USA