Precor EFX 833, EFX 883 warranty Threading the Cable Assembly P30, Console positioning on base unit

Page 38

36

Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 883 / 833

Threading the Cable Assembly (P30)

Earlier in the installation, you threaded the necessary cables through the frame of the base unit and out the passthrough opening in the console mount. As you line up the back plate on the console with the console mount, you must make sure that the cable assembly passes correctly through the openings in both components.

Important: Before you begin the following procedure, remove the rear cover from the control console. Set the cover and its mounting hardware aside for later use.

To thread the cable assembly:

1.Make sure that as much of each cable as possible passes through the opening in the middle of the console mount on the base unit.

2.Position the console over the console mount.

3.Rest the console on the console mount so that the notch on the bottom of the console’s back plate rests on the rectangular hook at the bottom of the console mount, as shown in the following figure.

Figure 30: Console positioning on base unit

4.Tilt the console forward until it stops. Use one hand to steady the console in this position, or ask your assistant to do so.

5.Pull all cables upward and forward until you can drape them over the top of the console’s back plate.

Image 38
Contents Assembling and Maintaining Elliptical Fitness Crosstrainers Page Page Intellectual Property Notice Edition InformationTrademark Note Important Safety Instructions Safety PrecautionsPage Educating Users Regulatory Notices for the Rfid Module Hazardous Materials and Proper DisposalProduct Recycling and Disposal Radio Frequency Interference RFIVoid the user’s authority to operate the equipment Federal Communications Commission, PartIndustry Canada Débranchez avant de réparerEuropean Applications Safety Approvals for Cardiovascular EquipmentRegulatory Notices for Cardiovascular Exercise Equipment Cardiovascular Type EquipmentUser’s authority to operate the equipment Obtaining Service Obtaining Updated Documentation IEC-320 C13 and C14 plugsTable of Contents Commercial Cardiovascular Equipment Limited Warranty To prepare the EFX for assembly Assembling the EFXFasteners Installation RequirementsHardware Kit not to scale Assembling the EFX Is properly installed Performing the AssemblyTo begin assembly Required ToolsRepeat steps 2 through 4 to attach the right upright support EFX cable path Cable connection points inside EFX base Lift cover replacement To mount the center column support on the frameTo tighten the fasteners properly Attachment of center column supportTighten the back fasteners on the upright supports To attach the handlebars Clamp screw location, EFX handlebar bracketTo tighten the handlebars completely Handrail attachment detailTo attach the water bottle holder Outer handrail caps attachmentTo attach the upright support covers Upright support cover attachment right-hand cover shownLeveling the EFX To level the unitBreaking in the Equipment Installing the Console Threading the Cable Assembly P80To thread the cable assembly Removing the access cover from the P80 consoleConnecting Cables P80 LocationTo connect the television cable Connecting the Television CableCable Connector Type Circuit Location Connecting the Ethernet and Base Unit Data Cables Connecting the television cableConnecting the Heart Rate Sensor Cable Connecting the Power CableCompleting the Console Installation P80 To complete the installationThreading the Cable Assembly P30 Connecting Cables P30 To verify that the heart rate display is operational Completing the Console Installation P30Verifying That the Heart Rate Display Is Operational Maintenance Daily CleaningDaily Inspection Weekly Maintenance Monthly MaintenanceLong-Term Storage Storing the Chest StrapMoving the Equipment Rate of Motion Self-Powered FeaturesMinimum requirements for operation Symptoms of a Low Battery Informational Displays Prior to ShutdownUsing the Optional Power Adapter Optional Power Adapter KitReplacing the Battery Warranty Periods and Coverage Commercial Cardiovascular Equipment Limited WarrantyLimited Warranty Conditions and Restrictions Exclusive Remedies Exclusion of Consequential and Incidental Damages Complete this portion and keep for your recordsCommercial Cardiovascular Equipment Limited Warranty Page Page Precor Incorporated Operating and Maintaining the P30 Console Page Page Edition Information Important Safety Instructions Operating and Maintaining the P30 Console  Do not lean on or pull on the console at any time Hazardous Materials and Proper Disposal Regulatory Notices for Cardiovascular Exercise Equipment 240 V Equipment Designated for U.S. Markets 120-volt, 20-amp power plug 240-volt, 20-amp power plugOperating and Maintaining the P30 Console 240 V Equipment Designated Operating and Maintaining the P30 Console Getting Started Activating the Console for Self-Powered EquipmentActivating the Console for Self-Powered Equipment Optional Use of the Power Adapter Identifying Parts of the Console Number Part Name Details Watts Number Part Name Details Setting Up the Console System Settings5 1 5 6 To view the Club Parameters settingsNavigational keys for the system setting modes Key Select Language All Equipment Setting Club Parameter ValuesSafety Code Treadmill only Set Units All EquipmentSet Cool Down Time All Equipment Set Max Workout Time All EquipmentSet Max Pause Time All Equipment To create a custom program Creating a Custom WorkoutValue Range on or OFF Custom Program keys Equipment Key Name DescriptionHidden Programs Treadmill only Set Speed Limit Treadmill onlySet Incline Limit Treadmill only Value Range 0 to Set Resistance Range Bike onlySet Crossramp Auto Level EFX Dual only Informational Displays values To view the System settingsViewing the Informational Displays Value Information providedEvent Log Product Value Information providedEvent Description of Event Number Csafe access keys Keys Function User ID Entry with Csafe EquipmentOperating and Maintaining the P30 Console Using the Touch Heart Rate Feature Introducing Users to the P30 ConsoleHeart rate target zones Interfere with pacemakers or other Using a Chest Strap TransmitterTo use a chest strap transmitter Heart rate strapUsing the Treadmill Safety Clip Restart switchAttaching the safety clip Treadmill Auto Stop Automatic Stop Function Starting a Workout WORKOUT, Press QUICKSTART, or Enter to BeginTo choose a language setting before you begin exercising Starting a Preset Programmed WorkoutSetting Options To choose a workout goal before you begin exercisingTo choose a unit of measure before you begin exercising Setting Options after You Begin a WorkoutTo enter your Age and Weight during a workout Pending Shutdown Self-Powered Equipment Pausing and Resuming an Exercise SessionPaused Externally Powered Equipment Ending a Session Operating and Maintaining the P30 Console Heart Rate ProgramsManual IntervalPerformance Weight LossVariety Cleaning the Console and Display To remove dust and dirt from the console20031 142nd Avenue NE January Box Woodinville, WA USA