ProForm PCTL04509.0 manual With a second Bolt Spacer 81, 3/8 x 4 Bolt 3/8 Star Washer

Page 8

3.

Identify the Right Upright (80) and the Right

3

 

 

 

 

 

 

Upright Spacer (82), which are marked with

 

 

 

80

 

 

“Right” stickers.

 

 

 

 

 

 

Insert the Upright Wire (79) through the Right

 

79

 

 

 

 

 

Upright Spacer (82) as shown. Set the Right

 

Wire Tie

 

 

79

 

Upright Spacer on the Base (87).

 

 

 

 

 

Have a second person hold the Right Upright

 

 

 

 

 

82

 

 

 

 

 

 

87

 

(80) near the Base (87). See the inset drawing.

 

 

 

 

 

 

Tie the wire tie in the Right Upright securely

 

 

 

 

 

 

 

around the end of the Upright Wire (79). Then,

 

 

 

 

 

 

 

pull the other end of the wire tie until the Upright

 

 

 

 

 

 

 

Wire is routed completely through the Right

 

 

 

 

 

 

 

Upright.

 

 

80

 

 

 

 

 

79

 

Wire

 

 

 

 

 

 

Tie

 

 

 

4. Hold a Bolt Spacer (81) inside the lower end of

4

 

 

 

9

 

 

the Right Upright (80). Insert a 3/8" x 4" Bolt (9)

 

 

 

 

 

with a 3/8" Star Washer (12) into the Right

 

 

 

 

 

 

 

Upright and the Bolt Spacer. Repeat this step

 

 

 

80

 

 

 

with a second Bolt Spacer (81), 3/8" x 4" Bolt

 

 

 

12

 

 

(9), and 3/8" Star Washer (12).

 

 

 

 

 

 

Hold the Right Upright (80) against the Right

 

 

 

 

79

81

 

Upright Spacer (82). Be careful not to pinch

 

 

 

 

 

 

the Upright Wire (79). Tighten the 3/8" x 4"

 

 

 

 

81

 

 

Bolts (9) until the heads of the Bolts touch the

 

 

 

 

83

 

Upright; do not fully tighten the Bolts yet.

 

 

 

 

82

 

Press a Base Cap (83) into the Base (87).

 

 

 

 

87

 

 

 

8

 

 

 

 

 

Image 8
Contents Contact OUR Customer SER- Vice Department Directly QUESTIONS?Model No. PCTL04509.0 Serial No Table of Contents Important Precautions Page Before YOU Begin Assembly Tighten the Nut the Wheel must turn freely Make sure that the power cord is unpluggedDo not fully fold the Frame yet With a second Bolt Spacer 81, 3/8 x 4 Bolt 3/8 Star Washer Upright do not fully tighten the Bolts yetTouch the Upright do not fully tighten Bolts yet Page Save the Crossbar and the two Screws for steps 11 Are not Connected PROPERLY, Console MAY be Damaged When YOUTurn on the Power Page PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the ConsoleInsert the key into the console HOW to Turn on the PowerHOW to USE the Manual Mode Measure your heart rate if desired. Before using HOW to USE a Preset Workout Select a preset workoutStart the workout Monitor your progress with the matrix and the displaysInformation Mode HOW to USE the Stereo Sound SystemHOW to Fold and Move the Treadmill HOW to Move the TreadmillHOW to Lower the Treadmill for USE Compatible with GFCI-equipped outlets TroubleshootingProblem The power turns off during use Problem The walking belt slows when walked on TopProblem Solution Exercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencyR1109A Key No. Qty. DescriptionDescription Exploded Drawing A-Model No. PCTL04509.0 R1109A Exploded Drawing B-Model No. PCTL04509.0 R1109A Exploded Drawing C-Model No. PCTL04509.0 Exploded Drawing D-Model No. PCTL04509.0 R1109A Ordering Replacement Parts Limited Warranty