JVC RX-778VBK manual Basic Settings, Adjusting the Front Speaker Output Balance

Page 14
SOURCE SELECTOR

English

Basic Settings

Some of the following settings are required after connecting and positioning your speakers in your listening room, while others will make operations easier.

IMPORTANT:

When using the remote control, check to see if its

remote control mode selector is set to the correct AUDIO/

position:TV/VCR

To operate this receiver, set it to “AUDIO/TV/

CATV/DBS

VCR” (except when selecting the DBS tuner as the source).

Adjusting the Front Speaker Output

Balance

If the sounds you hear from the front right and left speakers are unequal, you can adjust the speaker output balance.

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

On the front panel ONLY:

1.

Press BALANCE/SURROUND

BALANCE/SURROUND

 

ADJUST repeatedly until “L/R

ADJUST

 

 

 

BALANCE” appears on the

 

 

display.

 

 

The display changes to show the current setting.

2.

Turn MULTI JOG to adjust the

MULTI JOG

 

balance.

 

Turning it clockwise decreases the left channel output.

Turning it counterclockwise decreases the right channel output.

Changing the Source Name

When you have connected an MD recorder to the TAPE/MD jacks or the DBS tuner to the TV SOUND/DBS jacks on the rear panel, change the source name shown on the display when you select the MD recorder or DBS tuner as the source.

On the front panel ONLY:

1. When changing the source name from “TAPE” to “MD”:

Turn SOURCE SELECTOR until “TAPE” appears.

When changing the source name from “TV SOUND” to “DBS”:

Turn SOURCE SELECTOR until “TV SOUND” appears.

2. Press and hold SOURCE NAME

LOUDNESS

 

(LOUDNESS) until “ASSGN.

 

MD” or “ASSGN. DBS” appears

SOURCENAME

 

on the display.

 

To change the source name to “TAPE” or “TV SOUND,” repeat

the same procedure above — in step 1, select “MD” or “DBS” then press and hold SOURCE NAME (LOUDNESS).

Note:

Without changing the source name, you can still use the connected components. However, there may be some inconvenience.

“TAPE” or “TV SOUND” will appear on the display when you select the MD recorder or DBS tuner.

You cannot use the digital input (see page 13) for the MD recorder and the DBS tuner.

You cannot use the COMPU LINK remote control system (see page 33) to operate the MD recorder.

Setting the Subwoofer Information

Register whether or not you have connected a subwoofer.

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

On the front panel ONLY:

1. Press SETTING repeatedly until

SETTING

 

“SUBWOOFER” appears on the

 

display.

 

The display changes to show the current setting.

 

 

MULTI JOG

2.Turn MULTI JOG to register whether you have connected a subwoofer or not.

As you turn it, the subwoofer setting alternates between “YES” or “NO.”

YES: Select this when a subwoofer is used.

NO: Select this when no subwoofer is used.

Digital Input (DIGITAL IN) Terminal

Setting

When you use the digital input terminals, you have to register what components are connected to which terminals (DIGITAL IN 1/2).

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

12

Image 14
Contents RX-778VBK Mises en garde, précautions et indications diverses Table of Contents Front Panel Remote ControlParts Identification Getting Started Before Installation Connecting the FM and AM AntennasChecking the Supplied Accessories Connecting the front speakers Connecting the SpeakersBasic connecting procedure AM Antenna ConnectionsWhen you connect two sets of front speakers Connecting the subwoofer speakerCase 1 When you connect only one set of front speakers Audio component connections Connecting Audio/Video ComponentsAnalog connections DBS tuner Video component connectionsDVD player To composite video outputPlug the power cord into an AC outlet Connecting the Power CordPutting Batteries in the Remote Control Replace the coverBasic Operations Turning the Power On and Off StandbyFrom the remote control Selecting the Source to PlayATT. briefly while viewing Adjusting the VolumeSelecting the Front Speakers EtcAdjusting the Subwoofer Output Level Attenuating the Input SignalListening at Low Volume Loudness Muting the SoundSetting the Subwoofer Information Basic SettingsAdjusting the Front Speaker Output Balance Digital Input Digital in Terminal SettingSelecting the Analog or Digital Input Mode Showing the Text Information on DisplayCenter Delay Time Setting Setting the Speakers for the DSP ModesRear Delay appears on Display Front, Center, and Rear Speaker SettingRange COMP. Dynamic Range Compression appears on Display Frequency appears on the displayLFE ATT Low Frequency Effect Attenuator appears on Display Using the Sleep Timer Storing the Basic Settings Adjustments One Touch OperationAdjust the sound using the functions listed above Press ONE Touch OPERATION. OnetouchoperationReceiving Radio Broadcasts Using Preset TuningTuning in Stations Manually Tune in a preset station Assigning Names to Preset StationsSelecting the FM Reception Mode Turn Multi JOG to selectSelecting Your Favorite SEA Mode Using the SEA ModesCreating Your Own SEA Mode DAP modes Using the DSP Modes3D-PHONIC modes JVC Theater Surround Surround modesDolby Surround Dolby Digital and Dolby Pro Logic Rear Available DSP Modes According to the Speaker ArrangementFront Adjusting the 3D-PHONIC Modes Adjusting the DAP ModesAdjusting the Surround Modes Press Dolby Surround to Activate an appropriate Surround Mode PRO Logic or DolbyPress Test again to stop the test tone. Test Repeatedly until Theater orTo adjust the right rear speaker level, press Theater or DIG Theater appears on DisplayActivating the DSP Modes Press Menu Using the On-Screen MenusWhen you finish, press Exit Press % / Þto move to VisualPress %/ Þto move to Sound CONTROL, then press @/ # Press % / Þto move to Surround LEVEL, then press @/ #Press %/ Þto move to Sound CONTROL, then press @ / # Press %/ Þ/ @/ # to adjust the SEA mode as you wantPress SET to store the setting into the SEA Usermode Press %/ Þto move to SEA, then press @/ #Press % / Þto move To Tuner CONTROL, then press @/ # Press %/ Þto move To SETTING, then press @/ #Setting the Basic Setting Items Also see Assigning Names to Preset Stations Press %/ Þto move to Preset NAME, then press SETStoring the Preset Stations Also see Press %/ Þ/ @/ # to Move in front of a character you wantSame time Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Automatic Source SelectionDisplaying the Disc Information on the TV screen Text Compu Link Remote Control SystemCD player MD recorder Disc Search Only for CD PlayerTo exit from the Disc information screen Press Text Display while CD or MD is selected as the sourceShowing the Disc Information on the TV Screen Disc Information screen appears on the TVPress %/ Þto move to Performer Then press SET Press Text Display while CD is selected as the sourcePress %/ Þto move to SEARCH, then Press SET Press SET againEntering the Disc Information Press %/ Þto move to Search Then press SETPress % / Þto move to Title Input Then press SET Search for a disc by its genrePress Text Display while MD is selected as the source Enter the disc title, referring to steps 3Press %/ Þto move to the genre you want, then press SET Press %/ Þto move to Title Input Then press SETIf the AV Compu Link terminal on the TV is AV Compu Link EX AV Compu Link Remote Control SystemIf the AV Compu Link terminal on the TV is RECEIVER/AMP One-Touch Video Play Automatic Selection of TV’s Input ModeAutomatic Power On/Off One-Touch DVD PlayTuner Operating JVC’s Audio/Video ComponentsSound control section Amplifier CD playerCassette deck To operate JVC’s video components using this remote controlTurntable MD recorderOperating Other Manufacturers’ Video Equipment Release TV/CATV/DBS PowerIf there are more than one code listed for your brand of TV Try to operate your TV by pressing TV/CATVIf there are more than one code listed for your brand Release VCR PowerTry to operate your VCR by pressing VCR Power Manufacturer CodesTroubleshooting Problem Possible Cause SolutionFM tuner IHF SpecificationsAmplifier AM tunerEN, FR 0599HIMMDWJEM