JVC RX-778VBK manual Connecting the subwoofer speaker, When you connect two sets of front speakers

Page 7

About the speaker impedance	Connecting the rear and center speakers
The required speaker impedance of the front speakers does differ	Connect rear speakers to the REAR SPEAKERS terminals and a
depending on whether both the FRONT SPEAKERS 1 and FRONT	center speaker to the CENTER SPEAKER terminals.
SPEAKERS 2 terminals are used or only one of them is used.

English

CASE 1 When you connect only one set of front speakers

Front	Front
speaker	speaker
1	1

Use front speakers with 8 – 16 ohmimpedance.

	CASE 2		When you connect two sets of front speakers


			Front	Front
			speaker	speaker
			2	2
	Front			Front
	speaker			speaker
	1			1

Use front speakers 16 – 32 ohmimpedance.

CAUTION:

Use speakers with the SPEAKER IMPEDANCE indicated by the speaker terminals.

	CENTER		REAR
	SPEAKER	SPEAKERS
Center speaker		RIGHT	LEFT
Left rear	Right rear
speaker	speaker

Connecting the subwoofer speaker

You can enhance the bass by connecting a subwoofer. Connect the input jack of a powered subwoofer to the SUBWOOFER OUT jack on the rear panel, using a cable with RCA pin plugs (not supplied).

SUBWOOFER

OUT

Powered subwoofer

5

Image 7

Contents RX-778VBK Mises en garde, précautions et indications diverses Table of Contents Parts Identification Remote ControlFront Panel Checking the Supplied Accessories Before Installation Connecting the FM and AM AntennasGetting Started AM Antenna Connections Connecting the SpeakersBasic connecting procedure Connecting the front speakersCase 1 When you connect only one set of front speakers Connecting the subwoofer speakerWhen you connect two sets of front speakers Analog connections Connecting Audio/Video ComponentsAudio component connections To composite video output Video component connectionsDVD player DBS tunerReplace the cover Connecting the Power CordPutting Batteries in the Remote Control Plug the power cord into an AC outletSelecting the Source to Play Turning the Power On and Off StandbyFrom the remote control Basic OperationsEtc Adjusting the VolumeSelecting the Front Speakers ATT. briefly while viewingMuting the Sound Attenuating the Input SignalListening at Low Volume Loudness Adjusting the Subwoofer Output LevelDigital Input Digital in Terminal Setting Basic SettingsAdjusting the Front Speaker Output Balance Setting the Subwoofer InformationShowing the Text Information on Display Selecting the Analog or Digital Input ModeFront, Center, and Rear Speaker Setting Setting the Speakers for the DSP ModesRear Delay appears on Display Center Delay Time SettingLFE ATT Low Frequency Effect Attenuator appears on Display Frequency appears on the displayRange COMP. Dynamic Range Compression appears on Display Press ONE Touch OPERATION. Onetouchoperation Storing the Basic Settings Adjustments One Touch OperationAdjust the sound using the functions listed above Using the Sleep TimerTuning in Stations Manually Using Preset TuningReceiving Radio Broadcasts Turn Multi JOG to select Assigning Names to Preset StationsSelecting the FM Reception Mode Tune in a preset stationCreating Your Own SEA Mode Using the SEA ModesSelecting Your Favorite SEA Mode 3D-PHONIC modes Using the DSP ModesDAP modes Dolby Surround Dolby Digital and Dolby Pro Logic Surround modesJVC Theater Surround Front Available DSP Modes According to the Speaker ArrangementRear Adjusting the DAP Modes Adjusting the 3D-PHONIC ModesAdjusting the Surround Modes Repeatedly until Theater or Activate an appropriate Surround Mode PRO Logic or DolbyPress Test again to stop the test tone. Test Press Dolby Surround toTheater or DIG Theater appears on Display To adjust the right rear speaker level, pressActivating the DSP Modes Press % / Þto move to Visual Using the On-Screen MenusWhen you finish, press Exit Press MenuPress % / Þto move to Surround LEVEL, then press @/ # Press %/ Þto move to Sound CONTROL, then press @/ #Press %/ Þto move to SEA, then press @/ # Press %/ Þ/ @/ # to adjust the SEA mode as you wantPress SET to store the setting into the SEA Usermode Press %/ Þto move to Sound CONTROL, then press @ / #Setting the Basic Setting Items Also see Press %/ Þto move To SETTING, then press @/ #Press % / Þto move To Tuner CONTROL, then press @/ # Press %/ Þ/ @/ # to Move in front of a character you want Press %/ Þto move to Preset NAME, then press SETStoring the Preset Stations Also see Assigning Names to Preset StationsAutomatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Same timeDisc Search Only for CD Player Text Compu Link Remote Control SystemCD player MD recorder Displaying the Disc Information on the TV screenDisc Information screen appears on the TV Press Text Display while CD or MD is selected as the sourceShowing the Disc Information on the TV Screen To exit from the Disc information screenPress SET again Press Text Display while CD is selected as the sourcePress %/ Þto move to SEARCH, then Press SET Press %/ Þto move to Performer Then press SETSearch for a disc by its genre Press %/ Þto move to Search Then press SETPress % / Þto move to Title Input Then press SET Entering the Disc InformationPress %/ Þto move to Title Input Then press SET Enter the disc title, referring to steps 3Press %/ Þto move to the genre you want, then press SET Press Text Display while MD is selected as the sourceIf the AV Compu Link terminal on the TV is RECEIVER/AMP AV Compu Link Remote Control SystemIf the AV Compu Link terminal on the TV is AV Compu Link EX One-Touch DVD Play Automatic Selection of TV’s Input ModeAutomatic Power On/Off One-Touch Video PlayCD player Operating JVC’s Audio/Video ComponentsSound control section Amplifier TunerMD recorder To operate JVC’s video components using this remote controlTurntable Cassette deckTry to operate your TV by pressing TV/CATV Release TV/CATV/DBS PowerIf there are more than one code listed for your brand of TV Operating Other Manufacturers’ Video EquipmentManufacturer Codes Release VCR PowerTry to operate your VCR by pressing VCR Power If there are more than one code listed for your brandProblem Possible Cause Solution TroubleshootingAM tuner SpecificationsAmplifier FM tuner IHFEN, FR 0599HIMMDWJEM