English
To change the transmittable signals for operating a CATV converter or DBS tuner
1.Set the remote control mode to “CATV/DBS.”
2.Press and hold TV/CATV/DBS POWER.
3.Press TV/DBS.
4.Enter manufacturer’s code (three digits) using
buttons 1 – 9, and 0.
See the list below.
Examples: For a Pioneer product, press 1, then 3.
For a Sony product, press 2, then 0.
5. Release TV/CATV/DBS POWER.
After setting the remote control mode selector to “CATV/DBS,” you can perform the following operations on the CATV convertor or on the DBS tuner:
TV/CATV/DBS POWER Turns on and off the CATV converter
| or DBS tuner. |
CHANNEL | Changes the channels. |
1 – 10, 0, 100+ (+10): | Selects the channel. |
| 100+ (+10) button will function as |
| the ENTER button if your equipment |
| requires pressing ENTER after |
| selecting a channel number. |
Note:
Refer to the manual supplied with your CATV converter or DBS tuner.
6. Try to operate your CATV converter or DBS tuner by pressing TV/CATV/DBS POWER.
When your CATV converter or DBS tuner turns on or off, you have entered the correct code.
If there are more than one code listed for your brand of
CATV converter or DBS tuner, try each one until the correct one is entered.
Manufacturer | Codes |
GI/JERROLD | 01, 02, 03, 04, 05, |
| 06, 07, 08 |
|
|
HAMLIN/REGAL | 15, 16, 17, 18 |
|
|
PIONEER | 13, 14 |
RCA | 19 |
|
|
SCIENTIFIC ATLANTA | 09, 10 |
SONY | 20 |
ZENITH | 11, 12 |
Manufacturers’ codes are subject to change without notice. If they are changed, this remote control cannot operate the equipment.
To change the transmittable signals for operating another manufacturer’s VCR
1.Set the remote control mode to “AUDIO/TV/ VCR.”
2.Press and hold VCR POWER.
3.Press VCR.
4.Enter manufacturer’s code (two digits) using
buttons 1 – 9, and 0.
See the list below.
Examples: For a JVC product, press 0, then 1.
For a Funai product, press 1, then 0.
5. Release VCR POWER.
Following button can be used for operating the VCR (with the remote control mode selector set to “AUDIO/TV/VCR”):
VCR POWER: Turns on and off the VCR.
After pressing VCR or VCR CONTROL (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations on the VCR:
CHANNEL | Changes the TV channels on the VCR. |
1 – 10, 0, 100+ (+10): | Selects the TV channels. |
| 100+ (+10) button will function as |
| the ENTER button if your VCR |
| requires pressing ENTER after |
| selecting a channel number. |
PLAY: | Starts playback. |
1: | Rewinds a video tape. |
Á: | Fast winds a video tape. |
STOP: | Stops operation. |
PAUSE: | Pauses. |
¦ REC: | Starts recording or enters recording |
| pause. |
Notes:
•Refer to the manual supplied with your VCR.
•You can use either VCR button or the VCR CONTROL button to activate the buttons listed above. If you press VCR, the playing source also changes. On the other hand, if you press VCR CONTROL, the playing source does not change.
6.Try to operate your VCR by pressing VCR POWER.
When your VCR turns on or off, you have entered the correct code.
If there are more than one code listed for your brand of
VCR, try each one until the correct one is entered.
Manufacturer | Codes | Manufacturer | Codes |
|
|
|
|
JVC | 01, 02, 03 | PHILIPS | 09 |
|
|
|
|
EMERSON | 11, 26 | RCA | 05, 06 |
|
|
|
|
FISHER | 29 | SAMSUNG | 24 |
|
|
|
|
FUNAI | 10, 14, 15, 16 | SANYO | 21, 22, 23 |
GOLD STAR | 12 | SHARP | 27, 28 |
|
|
|
|
HITACHI | 04 | SHINTOM | 30 |
MITSUBISHI | 13 | SONY | 18, 19, 20 |
NEC | 25 | TOSHIBA | 26 |
|
|
|
|
PANASONIC | 07, 17 | ZENITH | 08 |
|
|
|
|
Manufacturers’ codes are subject to change without notice. If they are changed, this remote control cannot operate the equipment.
44