JVC RX-778VBK Connecting Audio/Video Components, Analog connections, Audio component connections

Page 8

English

Connecting Audio/Video Components

Cassette deck or MD recorder

You can connect the following audio/video components to this receiver. Refer also to the manuals supplied with your components.

Audio Components	Video Components

• Turntable	• DVD player*

• CD player*	• TV

• Cassette deck	• DBS tuner*

or MD recorder*	• VCR

*You can connect these components using the methods described in “Analog connections” (below) or in “Digital connections” (see page 8).

Analog connections

Audio component connections

To audio input

To audio input

Cassette deck

To audio output

RIGHT

LEFT

AUDIO

PHONO

CD

OUT

(REC)

TAPE

IN

(PLAY)

MD recorder

To audio output

Use the cables with RCA pin plugs (not supplied).

Connect the white plug to the audio left jack, and the red plug to the audio right jack.

CAUTION:

If you connect a sound-enhancing device such as a graphic equalizer between the source components and this receiver, the sound output through this receiver may be distorted.

Turntable

If an earth cable is provided for your turntable, connect the cable to the screw marked (H) on the rear panel.

RIGHT	LEFT AUDIO
Turntable	PHONO
	CD
	OUT
	(REC)
	TAPE
To audio output	/MD
To audio output	IN
	(PLAY)

Note:

Any turntables incorporating a small-output cartridge such as an MC (moving-coil type) must be connected to this receiver through a commercial head amplifier or step-up transformer. Direct connection may result in insufficient volume.

CD player

RIGHT

LEFT AUDIO

PHONO

CD player

	CD
	OUT
	(REC)
To audio output	TAPE
To audio output	/MD
	IN
	(PLAY)

Note:

You can connect either a cassette deck or an MD recorder to the TAPE/MD jacks. When connecting an MD recorder to the TAPE/MD jacks, change the source name, which will be shown on the display when selected as the source, to “MD.” See page 12 for details.

If your audio components have a COMPU LINK-3 or TEXT COMPU LINK terminal

•See also page 33 for detailed information about the connection and the COMPU LINK-3 remote control system.

•See also page 34 for detailed information about the connection and the TEXT COMPU LINK remote control system.

6

Image 8

Contents RX-778VBK Mises en garde, précautions et indications diverses Table of Contents Front Panel Remote ControlParts Identification Getting Started Before Installation Connecting the FM and AM AntennasChecking the Supplied Accessories Connecting the Speakers Basic connecting procedureConnecting the front speakers AM Antenna ConnectionsWhen you connect two sets of front speakers Connecting the subwoofer speakerCase 1 When you connect only one set of front speakers Audio component connections Connecting Audio/Video ComponentsAnalog connections Video component connections DVD playerDBS tuner To composite video outputConnecting the Power Cord Putting Batteries in the Remote ControlPlug the power cord into an AC outlet Replace the coverTurning the Power On and Off Standby From the remote controlBasic Operations Selecting the Source to PlayAdjusting the Volume Selecting the Front SpeakersATT. briefly while viewing EtcAttenuating the Input Signal Listening at Low Volume LoudnessAdjusting the Subwoofer Output Level Muting the SoundBasic Settings Adjusting the Front Speaker Output BalanceSetting the Subwoofer Information Digital Input Digital in Terminal SettingSelecting the Analog or Digital Input Mode Showing the Text Information on DisplaySetting the Speakers for the DSP Modes Rear Delay appears on DisplayCenter Delay Time Setting Front, Center, and Rear Speaker SettingRange COMP. Dynamic Range Compression appears on Display Frequency appears on the displayLFE ATT Low Frequency Effect Attenuator appears on Display Storing the Basic Settings Adjustments One Touch Operation Adjust the sound using the functions listed aboveUsing the Sleep Timer Press ONE Touch OPERATION. OnetouchoperationReceiving Radio Broadcasts Using Preset TuningTuning in Stations Manually Assigning Names to Preset Stations Selecting the FM Reception ModeTune in a preset station Turn Multi JOG to selectSelecting Your Favorite SEA Mode Using the SEA ModesCreating Your Own SEA Mode DAP modes Using the DSP Modes3D-PHONIC modes JVC Theater Surround Surround modesDolby Surround Dolby Digital and Dolby Pro Logic Rear Available DSP Modes According to the Speaker ArrangementFront Adjusting the 3D-PHONIC Modes Adjusting the DAP ModesAdjusting the Surround Modes Activate an appropriate Surround Mode PRO Logic or Dolby Press Test again to stop the test tone. TestPress Dolby Surround to Repeatedly until Theater orTo adjust the right rear speaker level, press Theater or DIG Theater appears on DisplayActivating the DSP Modes Using the On-Screen Menus When you finish, press ExitPress Menu Press % / Þto move to VisualPress %/ Þto move to Sound CONTROL, then press @/ # Press % / Þto move to Surround LEVEL, then press @/ #Press %/ Þ/ @/ # to adjust the SEA mode as you want Press SET to store the setting into the SEA UsermodePress %/ Þto move to Sound CONTROL, then press @ / # Press %/ Þto move to SEA, then press @/ #Press % / Þto move To Tuner CONTROL, then press @/ # Press %/ Þto move To SETTING, then press @/ #Setting the Basic Setting Items Also see Press %/ Þto move to Preset NAME, then press SET Storing the Preset Stations Also seeAssigning Names to Preset Stations Press %/ Þ/ @/ # to Move in front of a character you wantCompu Link Remote Control System Remote Control through the Remote Sensor on the ReceiverSame time Automatic Source SelectionText Compu Link Remote Control System CD player MD recorderDisplaying the Disc Information on the TV screen Disc Search Only for CD PlayerPress Text Display while CD or MD is selected as the source Showing the Disc Information on the TV ScreenTo exit from the Disc information screen Disc Information screen appears on the TVPress Text Display while CD is selected as the source Press %/ Þto move to SEARCH, then Press SETPress %/ Þto move to Performer Then press SET Press SET againPress %/ Þto move to Search Then press SET Press % / Þto move to Title Input Then press SETEntering the Disc Information Search for a disc by its genreEnter the disc title, referring to steps 3 Press %/ Þto move to the genre you want, then press SETPress Text Display while MD is selected as the source Press %/ Þto move to Title Input Then press SETIf the AV Compu Link terminal on the TV is AV Compu Link EX AV Compu Link Remote Control SystemIf the AV Compu Link terminal on the TV is RECEIVER/AMP Automatic Selection of TV’s Input Mode Automatic Power On/OffOne-Touch Video Play One-Touch DVD PlayOperating JVC’s Audio/Video Components Sound control section AmplifierTuner CD playerTo operate JVC’s video components using this remote control TurntableCassette deck MD recorderRelease TV/CATV/DBS Power If there are more than one code listed for your brand of TVOperating Other Manufacturers’ Video Equipment Try to operate your TV by pressing TV/CATVRelease VCR Power Try to operate your VCR by pressing VCR PowerIf there are more than one code listed for your brand Manufacturer CodesTroubleshooting Problem Possible Cause SolutionSpecifications AmplifierFM tuner IHF AM tunerEN, FR 0599HIMMDWJEM