JVC RX-778VBK manual Getting Started, Before Installation Connecting the FM and AM Antennas

Page 5

Getting Started

This section explains how to connect audio/video components and speakers to the receiver, and how to connect the power supply.

Before Installation

Connecting the FM and AM Antennas

English

General

•Be sure your hands are dry.

•Turn the power off to all components.

•Read the manuals supplied with the components you are going to connect.

Locations

•Install the receiver in a location that is level and protected from moisture.

•The temperature around the receiver must be between –5˚ and 35˚ C (23˚ and 95˚ F).

•Make sure there is good ventilation around the receiver. Poor ventilation could cause overheating and damage the receiver.

Handling the receiver

•Do not insert any metal object into the receiver.

•Do not disassemble the receiver or remove screws, covers, or cabinet.

•Do not expose the receiver to rain or moisture.

Checking the Supplied Accessories

Check to be sure you have all of the following items, which are supplied with the receiver.

The number in the parentheses indicates quantity of the pieces supplied.

•Remote Control (1)

•Batteries (2)

•AM Loop Antenna (1)

•FM Antenna (1)

If anything is missing, contact your dealer immediately.

FM Antenna Connections

A	ANTENNA	75	B	ANTENNA	75
	FM			FM
	COAXIAL			COAXIAL
	AM	AM		AM	AM
		EXT			EXT
	LOOP			LOOP

			FM Antenna
ANTENNA			Extend the supplied FM antenna horizontally.
	FM 75
	COAXIAL

AM	Outdoor FM Antenna Cable
LOOP

AM

EXT

A. Using the Supplied FM Antenna

The FM antenna provided can be connected to the FM 75Ω COAXIAL terminal as temporary measure.

B. Using the Standard Type Connector (Not Supplied)

A standard type connector should be connected to the FM 75Ω COAXIAL terminal.

Note:

If reception is poor, connect the outdoor antenna.

Before attaching a 75Ω coaxial cable (the kind with a round wire going to an outdoor antenna), disconnect the supplied FM antenna.

3

Image 5

Contents RX-778VBK Mises en garde, précautions et indications diverses Table of Contents Front Panel Remote ControlParts Identification Getting Started Before Installation Connecting the FM and AM AntennasChecking the Supplied Accessories Basic connecting procedure Connecting the SpeakersConnecting the front speakers AM Antenna ConnectionsWhen you connect two sets of front speakers Connecting the subwoofer speakerCase 1 When you connect only one set of front speakers Audio component connections Connecting Audio/Video ComponentsAnalog connections DVD player Video component connectionsDBS tuner To composite video outputPutting Batteries in the Remote Control Connecting the Power CordPlug the power cord into an AC outlet Replace the coverFrom the remote control Turning the Power On and Off StandbyBasic Operations Selecting the Source to PlaySelecting the Front Speakers Adjusting the VolumeATT. briefly while viewing EtcListening at Low Volume Loudness Attenuating the Input SignalAdjusting the Subwoofer Output Level Muting the SoundAdjusting the Front Speaker Output Balance Basic SettingsSetting the Subwoofer Information Digital Input Digital in Terminal SettingShowing the Text Information on Display Selecting the Analog or Digital Input ModeRear Delay appears on Display Setting the Speakers for the DSP ModesCenter Delay Time Setting Front, Center, and Rear Speaker SettingRange COMP. Dynamic Range Compression appears on Display Frequency appears on the displayLFE ATT Low Frequency Effect Attenuator appears on Display Adjust the sound using the functions listed above Storing the Basic Settings Adjustments One Touch OperationUsing the Sleep Timer Press ONE Touch OPERATION. OnetouchoperationReceiving Radio Broadcasts Using Preset TuningTuning in Stations Manually Selecting the FM Reception Mode Assigning Names to Preset StationsTune in a preset station Turn Multi JOG to selectSelecting Your Favorite SEA Mode Using the SEA ModesCreating Your Own SEA Mode DAP modes Using the DSP Modes3D-PHONIC modes JVC Theater Surround Surround modesDolby Surround Dolby Digital and Dolby Pro Logic Rear Available DSP Modes According to the Speaker ArrangementFront Adjusting the DAP Modes Adjusting the 3D-PHONIC ModesAdjusting the Surround Modes Press Test again to stop the test tone. Test Activate an appropriate Surround Mode PRO Logic or DolbyPress Dolby Surround to Repeatedly until Theater orTheater or DIG Theater appears on Display To adjust the right rear speaker level, pressActivating the DSP Modes When you finish, press Exit Using the On-Screen MenusPress Menu Press % / Þto move to VisualPress % / Þto move to Surround LEVEL, then press @/ # Press %/ Þto move to Sound CONTROL, then press @/ #Press SET to store the setting into the SEA Usermode Press %/ Þ/ @/ # to adjust the SEA mode as you wantPress %/ Þto move to Sound CONTROL, then press @ / # Press %/ Þto move to SEA, then press @/ #Press % / Þto move To Tuner CONTROL, then press @/ # Press %/ Þto move To SETTING, then press @/ #Setting the Basic Setting Items Also see Storing the Preset Stations Also see Press %/ Þto move to Preset NAME, then press SETAssigning Names to Preset Stations Press %/ Þ/ @/ # to Move in front of a character you wantRemote Control through the Remote Sensor on the Receiver Compu Link Remote Control SystemSame time Automatic Source SelectionCD player MD recorder Text Compu Link Remote Control SystemDisplaying the Disc Information on the TV screen Disc Search Only for CD PlayerShowing the Disc Information on the TV Screen Press Text Display while CD or MD is selected as the sourceTo exit from the Disc information screen Disc Information screen appears on the TVPress %/ Þto move to SEARCH, then Press SET Press Text Display while CD is selected as the sourcePress %/ Þto move to Performer Then press SET Press SET againPress % / Þto move to Title Input Then press SET Press %/ Þto move to Search Then press SETEntering the Disc Information Search for a disc by its genrePress %/ Þto move to the genre you want, then press SET Enter the disc title, referring to steps 3Press Text Display while MD is selected as the source Press %/ Þto move to Title Input Then press SETIf the AV Compu Link terminal on the TV is AV Compu Link EX AV Compu Link Remote Control SystemIf the AV Compu Link terminal on the TV is RECEIVER/AMP Automatic Power On/Off Automatic Selection of TV’s Input ModeOne-Touch Video Play One-Touch DVD PlaySound control section Amplifier Operating JVC’s Audio/Video ComponentsTuner CD playerTurntable To operate JVC’s video components using this remote controlCassette deck MD recorderIf there are more than one code listed for your brand of TV Release TV/CATV/DBS PowerOperating Other Manufacturers’ Video Equipment Try to operate your TV by pressing TV/CATVTry to operate your VCR by pressing VCR Power Release VCR PowerIf there are more than one code listed for your brand Manufacturer CodesProblem Possible Cause Solution TroubleshootingAmplifier SpecificationsFM tuner IHF AM tunerEN, FR 0599HIMMDWJEM