JVC RX-778VBK manual Press Test again to stop the test tone. Test, Press Dolby Surround to

Page 27

Notes:

•You can adjust the speaker output levels without outputting the test tone.

•No test tone comes out of the center speaker when “CENTER SPK” is set to “NONE” (see page 14).

•No test tone comes out of the rear speakers when “REAR SPK” is set to “NONE” (see page 14).

•If the TV is turned on and the proper video input is selected on the TV, the test tone screen will appear on the TV.

•The signal indicators also light on the display while the test tone

comes out of the speakers.

L

C R

L:Lights when the test tone comes out of the left front speaker.

C: Lights when the test tone comes out of

LS

RS

 

 

the center speaker.

 

 

R:Lights when the test tone comes out of the right front speaker.

2.Adjust the speaker output levels.

1)Press BALANCE/SURROUND ADJUST repeatedly until one of the indications appears on the display. “CENTER LEVEL”:

To adjust the center speaker level. “REAR L LEVEL”:

To adjust the left rear speaker level. “REAR R LEVEL”:

To adjust the right rear speaker level.

2)Turn MULTI JOG to adjust the selected speaker output level (from –10 dB to +10 dB).

3)Repeat 1) and 2) to adjust the other speaker output levels.

BALANCE/SURROUND

ADJUST

MULTI JOG

English

RS: Lights when the test tone comes out of the right rear speaker.

LS: Lights when the test tone comes out of the left rear speaker.

 

 

CNTR

4. Adjust the speaker output levels.

3

2

MENU

•To adjust the center speaker level, press CNTR –/+ (from –10 dB to +10 dB).

• To adjust the left rear speaker level, press

 

 

REAR•L

 

 

5

6

REAR•L –/+ (from –10 dB to +10 dB).

 

 

ENTER

• To adjust the right rear speaker level, press

 

 

 

REAR•R –/+ (from –10 dB to +10 dB).

 

 

REAR•R

 

 

8 9

5.Press TEST again to stop the test tone. TEST

4

On the front panel:

You can also use the buttons on the front panel to adjust the Surround modes. However, no test tone is available when using the buttons on the front panel. So, make adjustments while listening to the sound of the source played back.

1. Press DOLBY SURROUND to

DOLBY SURROUND

 

activate an appropriate Surround

 

mode — PRO LOGIC or DOLBY

 

DIGITAL.

 

•Each time you press the button, the Surround mode turns on and off alternately.

•When “PRO LOGIC” is selected, the PRO LOGIC indicator lights up on the display.

JVC Theater Surround adjustments

Before you start, remember...

•Make sure that you have set the speaker information correctly (see page 14).

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

•You cannot adjust the rear speaker output levels when you have set “REAR SPK” to “NONE.” See page 14.

•You cannot adjust the center speaker output level when you have set “CENTER SPK” to “NONE.” See page 14.

From the remote control:

1. Press SURROUND MODE

SURROUND

 

repeatedly until “THEATER” or

MODE

 

“DIG THEATER” appears on the display.

•When “THEATER” is selected, the PRO LOGIC, DSP, and THEATER indicators also light up on the display.

•When “DIG THEATER” is selected, the DSP, THEATER and

ÙDIGITAL indicators also light up on the display.

2. Press SOUND.

SOUND

 

The 10 keys are activated for sound adjustments.

25

Page 26 Page 28
Image 27
Page 26 Page 28
Contents RX-778VBK Mises en garde, précautions et indications diverses Table of Contents Remote Control Parts IdentificationFront Panel Before Installation Connecting the FM and AM Antennas Checking the Supplied AccessoriesGetting Started AM Antenna Connections Connecting the SpeakersBasic connecting procedure Connecting the front speakersConnecting the subwoofer speaker Case 1 When you connect only one set of front speakersWhen you connect two sets of front speakers Connecting Audio/Video Components Analog connectionsAudio component connections To composite video output Video component connectionsDVD player DBS tunerReplace the cover Connecting the Power CordPutting Batteries in the Remote Control Plug the power cord into an AC outletSelecting the Source to Play Turning the Power On and Off StandbyFrom the remote control Basic OperationsEtc Adjusting the VolumeSelecting the Front Speakers ATT. briefly while viewingMuting the Sound Attenuating the Input SignalListening at Low Volume Loudness Adjusting the Subwoofer Output LevelDigital Input Digital in Terminal Setting Basic SettingsAdjusting the Front Speaker Output Balance Setting the Subwoofer InformationShowing the Text Information on Display Selecting the Analog or Digital Input ModeFront, Center, and Rear Speaker Setting Setting the Speakers for the DSP ModesRear Delay appears on Display Center Delay Time SettingFrequency appears on the display LFE ATT Low Frequency Effect Attenuator appears on DisplayRange COMP. Dynamic Range Compression appears on Display Press ONE Touch OPERATION. Onetouchoperation Storing the Basic Settings Adjustments One Touch OperationAdjust the sound using the functions listed above Using the Sleep TimerUsing Preset Tuning Tuning in Stations ManuallyReceiving Radio Broadcasts Turn Multi JOG to select Assigning Names to Preset StationsSelecting the FM Reception Mode Tune in a preset stationUsing the SEA Modes Creating Your Own SEA ModeSelecting Your Favorite SEA Mode Using the DSP Modes 3D-PHONIC modesDAP modes Surround modes Dolby Surround Dolby Digital and Dolby Pro LogicJVC Theater Surround Available DSP Modes According to the Speaker Arrangement FrontRear Adjusting the DAP Modes Adjusting the 3D-PHONIC ModesAdjusting the Surround Modes Repeatedly until Theater or Activate an appropriate Surround Mode PRO Logic or DolbyPress Test again to stop the test tone. Test Press Dolby Surround toTheater or DIG Theater appears on Display To adjust the right rear speaker level, pressActivating the DSP Modes Press % / Þto move to Visual Using the On-Screen MenusWhen you finish, press Exit Press MenuPress % / Þto move to Surround LEVEL, then press @/ # Press %/ Þto move to Sound CONTROL, then press @/ #Press %/ Þto move to SEA, then press @/ # Press %/ Þ/ @/ # to adjust the SEA mode as you wantPress SET to store the setting into the SEA Usermode Press %/ Þto move to Sound CONTROL, then press @ / #Press %/ Þto move To SETTING, then press @/ # Setting the Basic Setting Items Also seePress % / Þto move To Tuner CONTROL, then press @/ # Press %/ Þ/ @/ # to Move in front of a character you want Press %/ Þto move to Preset NAME, then press SETStoring the Preset Stations Also see Assigning Names to Preset StationsAutomatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Same timeDisc Search Only for CD Player Text Compu Link Remote Control SystemCD player MD recorder Displaying the Disc Information on the TV screenDisc Information screen appears on the TV Press Text Display while CD or MD is selected as the sourceShowing the Disc Information on the TV Screen To exit from the Disc information screenPress SET again Press Text Display while CD is selected as the sourcePress %/ Þto move to SEARCH, then Press SET Press %/ Þto move to Performer Then press SETSearch for a disc by its genre Press %/ Þto move to Search Then press SETPress % / Þto move to Title Input Then press SET Entering the Disc InformationPress %/ Þto move to Title Input Then press SET Enter the disc title, referring to steps 3Press %/ Þto move to the genre you want, then press SET Press Text Display while MD is selected as the sourceAV Compu Link Remote Control System If the AV Compu Link terminal on the TV is RECEIVER/AMPIf the AV Compu Link terminal on the TV is AV Compu Link EX One-Touch DVD Play Automatic Selection of TV’s Input ModeAutomatic Power On/Off One-Touch Video PlayCD player Operating JVC’s Audio/Video ComponentsSound control section Amplifier TunerMD recorder To operate JVC’s video components using this remote controlTurntable Cassette deckTry to operate your TV by pressing TV/CATV Release TV/CATV/DBS PowerIf there are more than one code listed for your brand of TV Operating Other Manufacturers’ Video EquipmentManufacturer Codes Release VCR PowerTry to operate your VCR by pressing VCR Power If there are more than one code listed for your brandProblem Possible Cause Solution TroubleshootingAM tuner SpecificationsAmplifier FM tuner IHFEN, FR 0599HIMMDWJEM
Top Page Image Contents