ProForm PFTL49707.0 user manual Troubleshooting, Problem The power turns off during use, Top

Page 21

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please see the front cover of this manual.

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 12). Use only a single-outlet surge suppres- sor that meets all of the specifications described on page 12. Important: The treadmill is not com- patible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c.Check the reset/off circuit breaker located on the treadmill frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

c

Tripped

Reset

PROBLEM: The power turns off during use

SOLUTION: a. Check the reset/off circuit breaker located on the treadmill frame near the power cord (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key into the console.

d.If the treadmill still will not run, see the front cover of this manual.

PROBLEM: The displays of the console do not function properly

SOLUTION: a. Remove the key from the console and UNPLUG THE POWER CORD. Remove the two Foot Rail Screws

(4)and the two Hood Screws (86) and carefully re- move the Hood (1).

a86

4

1 4

Locate the Reed Switch (62) and the Magnet (67) on the left side of the Pulley (64). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8 in. (3 mm). If necessary, loosen the 3/4" Tek Screw (38), move the Reed Switch slightly, and then retighten the Screw. Reattach the Hood (not shown), and run the treadmill for a few minutes to check for a correct speed read- ing.

1/8 in.

64

38

 

62

67

Top

 

View

 

21

Image 21
Contents QUESTIONS? Model No. PFTL49707.0 Serial NoCall TOLL-FREE Table of Contents Important Precautions Page Before YOU Begin Assembly Latch Holes Wire Tie Large Outer side of the Frame Spacer facing See the left inset drawing. Identify the twoBolt yet See the left inset drawing. Identify the outerFront View Be careful not to pinch the wires. Next, thread Star Washers 19. Be careful not to pinch Upright WireNot tighten the Bolts yet Two 1/4 X 1/2 BoltsSide View View from Above Page Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerAvoid moving your hands. When your pulse Turn on the fan if desiredMeasure your heart rate if desired Select a trainer workout HOW to USE a Trainer WorkoutSelect a custom program HOW to Create a Custom ProgramHOW to USE a Custom Program HOW to USE the Dumbbells Information ModeHOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USETroubleshooting Problem The power turns off during useTop Problem The walking belt slows when walked on Exercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencyKey No. Qty Description Part LIST-Model No. PFTL49707.0Exploded Exploded Drawing B-Model No. PFTL49707.0 R0707A Exploded Drawing C-Model No. PFTL49707.0 Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT