ProForm 831.291710 user manual Into the corresponding connector in the Console Base

Page 6

3.Remove the Handrail Screw (53) from one of the

Handrails (1). Insert the Handrail into the tube at the top

of the left Upright (11), and align the hole in the Handrail with the slotted hole in the Upright. Loosely thread the Handrail Screw into the Handrail, rotate the Handrail until

the Screw is touching one end of the slotted hole, and then fully tighten the Screw.

Attach the other Handrail (1) to the right Upright (11) in the same way.

4.Place the Console Base (46) on the tubes on the Uprights

(11). Pull out just enough of the two Wires (21) to connect them to the connectors in the Console Base. Make a loop

with the indicated plastic tie around the Wires and insert the end through the tie holder on the bottom of the Console Base. Plug the Wire that has a red connector

into the corresponding connector in the Console Base.

The connectors should fit together without being forced; if they do not, rotate the connector on the

Wire and then plug it in.

Next, plug the other Wire into

the other connector in the Console Base.

Important:

Make sure that both Wires are fully inserted.

 

WARNING: Do not disconnect or connect the Wires

 

while the treadmill power cord is plugged in.

Pull the

plastic tie tight and cut off the end.

 

Refer to drawing 4b. Thread six Console Screws (99) into

the Uprights (11) and the Console Base (46). After all six

Console Screws have been started, tighten the Screws

until they are snug; do not overtighten the Screws.

5. Attach the Storage Latch (14) to the left Upright (11) with

two Small Screws (13). Be careful not to overtighten the Latch Screws.

3

 

 

 

53

53

 

 

1

Slotted

 

Hole

 

 

1

 

 

 

11

 

4a

 

 

 

46

 

21

 

21

11

Tie

 

4b

46

11

11

 

99

99

5

11

14 13

6. Make sure that all parts are properly tightened before you use the treadmill.Keep the included allen

wrench in a secure place. The allen wrench is used to adjust the walking belt (see page 13). To protect the floor or carpet, place a mat under the treadmill.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Model No Serial No Serial Number DecalSEARS, Roebuck and CO Hoffman ESTATES, IL Table of Contents Important PrecautionsNever leave the treadmill unattended while Not in useMove the Treadmill on Before YOU Begin For your benefit, read this manual carefully beforeBack Assembly Assembly requires two peopleExtension Leg with an Extension Leg Screw Plastic tie tight and cut off the end Into the corresponding connector in the Console BaseOther connector in the Console Base Until they are snug do not overtighten the ScrewsThis product must be grounded.If it should malfunc HOW to Plug in the Power CordPerformant Lube Grounded Outlet BoxBattery Installation Console DiagramAdjust the speed in small increments 14 for more informationReset position before the walking belt can be restarted Adjust the incline of the treadmill as desiredHOW to USE the Upper Body Arms HOW to Fold the Treadmill for StorageTreadmill, make sure to lift with your legs rather Your legs and keep your back straight HOW to Move the TreadmillHOW to Lower the Treadmill for USE Base Front WheelsProblem The power turns off during use TroubleshootingProblem The power does not turn on Remove the key from the consolePower Cord SolutionProblem ONE of the Upper Body Arms Squeaks During USE Exercise Intensity HOW to Measure Your Heart RateConditioning Guidelines Workout GuidelinesExercise Frequency Suggested StretchesFull 90 DAY Warranty SEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, ILRemove this Exploded Drawing and Part List from the Manual Part LIST-Model No Qty Description Key No. QtyR0502A
Top Page Image Contents